| blob | 823ff28732292480c17ff0f55b2d5b777f21a6de |
1 /*
2 * Adaptec 274x/284x/294x device driver firmware for Linux and FreeBSD.
3 *
4 * Copyright (c) 1994-1999 Justin Gibbs.
5 * All rights reserved.
6 *
7 * Redistribution and use in source and binary forms, with or without
8 * modification, are permitted provided that the following conditions
9 * are met:
10 * 1. Redistributions of source code must retain the above copyright
11 * notice, this list of conditions, and the following disclaimer,
12 * without modification, immediately at the beginning of the file.
13 * 2. The name of the author may not be used to endorse or promote products
14 * derived from this software without specific prior written permission.
15 *
16 * Where this Software is combined with software released under the terms of
17 * the GNU General Public License (GPL) and the terms of the GPL would require the
18 * combined work to also be released under the terms of the GPL, the terms
19 * and conditions of this License will apply in addition to those of the
20 * GPL with the exception of any terms or conditions of this License that
21 * conflict with, or are expressly prohibited by, the GPL.
22 *
23 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
24 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
25 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
26 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
27 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
28 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
29 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
30 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
31 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
32 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
33 * SUCH DAMAGE.
34 *
35 * $Id: aic7xxx.seq,v 1.77 1998/06/28 02:58:57 gibbs Exp $
36 */
38 #include "aic7xxx.reg"
39 #include "scsi_message.h"
41 /*
42 * A few words on the waiting SCB list:
43 * After starting the selection hardware, we check for reconnecting targets
44 * as well as for our selection to complete just in case the reselection wins
45 * bus arbitration. The problem with this is that we must keep track of the
46 * SCB that we've already pulled from the QINFIFO and started the selection
47 * on just in case the reselection wins so that we can retry the selection at
48 * a later time. This problem cannot be resolved by holding a single entry
49 * in scratch ram since a reconnecting target can request sense and this will
50 * create yet another SCB waiting for selection. The solution used here is to
51 * use byte 27 of the SCB as a pseudo-next pointer and to thread a list
52 * of SCBs that are awaiting selection. Since 0-0xfe are valid SCB indexes,
53 * SCB_LIST_NULL is 0xff which is out of range. An entry is also added to
54 * this list every time a request sense occurs or after completing a non-tagged
55 * command for which a second SCB has been queued. The sequencer will
56 * automatically consume the entries.
57 */
59 reset:
60 clr SCSISIGO; /* De-assert BSY */
61 and SXFRCTL1, ~BITBUCKET;
62 /* Always allow reselection */
63 mvi SCSISEQ, ENRSELI|ENAUTOATNP;
65 if ((p->features & AHC_CMD_CHAN) != 0) {
66 /* Ensure that no DMA operations are in progress */
67 clr CCSGCTL;
68 clr CCSCBCTL;
69 }
71 call clear_target_state;
72 poll_for_work:
73 and SXFRCTL0, ~SPIOEN;
74 if ((p->features & AHC_QUEUE_REGS) == 0) {
75 mov A, QINPOS;
76 }
77 poll_for_work_loop:
78 if ((p->features & AHC_QUEUE_REGS) == 0) {
79 and SEQCTL, ~PAUSEDIS;
80 }
81 test SSTAT0, SELDO|SELDI jnz selection;
82 test SCSISEQ, ENSELO jnz poll_for_work;
83 if ((p->features & AHC_TWIN) != 0) {
84 /*
85 * Twin channel devices cannot handle things like SELTO
86 * interrupts on the "background" channel. So, if we
87 * are selecting, keep polling the current channel util
88 * either a selection or reselection occurs.
89 */
90 xor SBLKCTL,SELBUSB; /* Toggle to the other bus */
91 test SSTAT0, SELDO|SELDI jnz selection;
92 test SCSISEQ, ENSELO jnz poll_for_work;
93 xor SBLKCTL,SELBUSB; /* Toggle back */
94 }
95 cmp WAITING_SCBH,SCB_LIST_NULL jne start_waiting;
96 test_queue:
97 /* Has the driver posted any work for us? */
98 if ((p->features & AHC_QUEUE_REGS) != 0) {
99 test QOFF_CTLSTA, SCB_AVAIL jz poll_for_work_loop;
100 mov NONE, SNSCB_QOFF;
101 inc QINPOS;
102 } else {
103 or SEQCTL, PAUSEDIS;
104 cmp KERNEL_QINPOS, A je poll_for_work_loop;
105 inc QINPOS;
106 and SEQCTL, ~PAUSEDIS;
107 }
109 /*
110 * We have at least one queued SCB now and we don't have any
111 * SCBs in the list of SCBs awaiting selection. If we have
112 * any SCBs available for use, pull the tag from the QINFIFO
113 * and get to work on it.
114 */
115 if ((p->flags & AHC_PAGESCBS) != 0) {
116 mov ALLZEROS call get_free_or_disc_scb;
117 }
119 dequeue_scb:
120 add A, -1, QINPOS;
121 mvi QINFIFO_OFFSET call fetch_byte;
123 if ((p->flags & AHC_PAGESCBS) == 0) {
124 /* In the non-paging case, the SCBID == hardware SCB index */
125 mov SCBPTR, RETURN_2;
126 }
127 dma_queued_scb:
128 /*
129 * DMA the SCB from host ram into the current SCB location.
130 */
131 mvi DMAPARAMS, HDMAEN|DIRECTION|FIFORESET;
132 mov RETURN_2 call dma_scb;
134 /*
135 * Preset the residual fields in case we never go through a data phase.
136 * This isn't done by the host so we can avoid a DMA to clear these
137 * fields for the normal case of I/O that completes without underrun
138 * or overrun conditions.
139 */
140 if ((p->features & AHC_CMD_CHAN) != 0) {
141 bmov SCB_RESID_DCNT, SCB_DATACNT, 3;
142 } else {
143 mov SCB_RESID_DCNT[0],SCB_DATACNT[0];
144 mov SCB_RESID_DCNT[1],SCB_DATACNT[1];
145 mov SCB_RESID_DCNT[2],SCB_DATACNT[2];
146 }
147 mov SCB_RESID_SGCNT, SCB_SGCOUNT;
149 start_scb:
150 /*
151 * Place us on the waiting list in case our selection
152 * doesn't win during bus arbitration.
153 */
154 mov SCB_NEXT,WAITING_SCBH;
155 mov WAITING_SCBH, SCBPTR;
156 start_waiting:
157 /*
158 * Pull the first entry off of the waiting SCB list.
159 */
160 mov SCBPTR, WAITING_SCBH;
161 call start_selection;
162 jmp poll_for_work;
164 start_selection:
165 if ((p->features & AHC_TWIN) != 0) {
166 and SINDEX,~SELBUSB,SBLKCTL;/* Clear channel select bit */
167 and A,SELBUSB,SCB_TCL; /* Get new channel bit */
168 or SINDEX,A;
169 mov SBLKCTL,SINDEX; /* select channel */
170 }
171 initialize_scsiid:
172 if ((p->features & AHC_ULTRA2) != 0) {
173 and A, TID, SCB_TCL; /* Get target ID */
174 and SCSIID_ULTRA2, OID; /* Clear old target */
175 or SCSIID_ULTRA2, A;
176 } else {
177 and A, TID, SCB_TCL; /* Get target ID */
178 and SCSIID, OID; /* Clear old target */
179 or SCSIID, A;
180 }
181 mov SCSIDATL, ALLZEROS; /* clear out the latched */
182 /* data register, this */
183 /* fixes a bug on some */
184 /* controllers where the */
185 /* last byte written to */
186 /* this register can leak */
187 /* onto the data bus at */
188 /* bad times, such as during */
189 /* selection timeouts */
190 mvi SCSISEQ, ENSELO|ENAUTOATNO|ENRSELI|ENAUTOATNP ret;
192 /*
193 * Initialize Ultra mode setting and clear the SCSI channel.
194 * SINDEX should contain any additional bit's the client wants
195 * set in SXFRCTL0.
196 */
197 initialize_channel:
198 or SXFRCTL0, CLRSTCNT|CLRCHN, SINDEX;
199 if ((p->features & AHC_ULTRA) != 0) {
200 ultra:
201 mvi SINDEX, ULTRA_ENB+1;
202 test SAVED_TCL, 0x80 jnz ultra_2; /* Target ID > 7 */
203 dec SINDEX;
204 ultra_2:
205 mov FUNCTION1,SAVED_TCL;
206 mov A,FUNCTION1;
207 test SINDIR, A jz ndx_dtr;
208 or SXFRCTL0, FAST20;
209 }
210 /*
211 * Initialize SCSIRATE with the appropriate value for this target.
212 * The SCSIRATE settings for each target are stored in an array
213 * based at TARG_SCSIRATE.
214 */
215 ndx_dtr:
216 shr A,4,SAVED_TCL;
217 if ((p->features & AHC_TWIN) != 0) {
218 test SBLKCTL,SELBUSB jz ndx_dtr_2;
219 or SAVED_TCL, SELBUSB;
220 or A,0x08; /* Channel B entries add 8 */
221 ndx_dtr_2:
222 }
224 if ((p->features & AHC_ULTRA2) != 0) {
225 add SINDEX, TARG_OFFSET, A;
226 mov SCSIOFFSET, SINDIR;
227 }
229 add SINDEX,TARG_SCSIRATE,A;
230 mov SCSIRATE,SINDIR ret;
233 selection:
234 test SSTAT0,SELDO jnz select_out;
235 /*
236 * Reselection has been initiated by a target. Make a note that we've been
237 * reselected, but haven't seen an IDENTIFY message from the target yet.
238 */
239 initiator_reselect:
240 mvi CLRSINT0, CLRSELDI;
241 /* XXX test for and handle ONE BIT condition */
242 and SAVED_TCL, SELID_MASK, SELID;
243 mvi CLRSINT1,CLRBUSFREE;
244 or SIMODE1, ENBUSFREE; /*
245 * We aren't expecting a
246 * bus free, so interrupt
247 * the kernel driver if it
248 * happens.
249 */
250 mvi SPIOEN call initialize_channel;
251 mvi MSG_OUT, MSG_NOOP; /* No message to send */
252 jmp ITloop;
254 /*
255 * After the selection, remove this SCB from the "waiting SCB"
256 * list. This is achieved by simply moving our "next" pointer into
257 * WAITING_SCBH. Our next pointer will be set to null the next time this
258 * SCB is used, so don't bother with it now.
259 */
260 select_out:
261 /* Turn off the selection hardware */
262 mvi SCSISEQ, ENRSELI|ENAUTOATNP; /*
263 * ATN on parity errors
264 * for "in" phases
265 */
266 mvi CLRSINT0, CLRSELDO;
267 mov SCBPTR, WAITING_SCBH;
268 mov WAITING_SCBH,SCB_NEXT;
269 mov SAVED_TCL, SCB_TCL;
270 mvi CLRSINT1,CLRBUSFREE;
271 or SIMODE1, ENBUSFREE; /*
272 * We aren't expecting a
273 * bus free, so interrupt
274 * the kernel driver if it
275 * happens.
276 */
277 mvi SPIOEN call initialize_channel;
278 /*
279 * As soon as we get a successful selection, the target should go
280 * into the message out phase since we have ATN asserted.
281 */
282 mvi MSG_OUT, MSG_IDENTIFYFLAG;
283 or SEQ_FLAGS, IDENTIFY_SEEN;
285 /*
286 * Main loop for information transfer phases. Wait for the target
287 * to assert REQ before checking MSG, C/D and I/O for the bus phase.
288 */
289 ITloop:
290 call phase_lock;
292 mov A, LASTPHASE;
294 test A, ~P_DATAIN jz p_data;
295 cmp A,P_COMMAND je p_command;
296 cmp A,P_MESGOUT je p_mesgout;
297 cmp A,P_STATUS je p_status;
298 cmp A,P_MESGIN je p_mesgin;
300 mvi INTSTAT,BAD_PHASE; /* unknown phase - signal driver */
301 jmp ITloop; /* Try reading the bus again. */
303 await_busfree:
304 and SIMODE1, ~ENBUSFREE;
305 call clear_target_state;
306 mov NONE, SCSIDATL; /* Ack the last byte */
307 and SXFRCTL0, ~SPIOEN;
308 test SSTAT1,REQINIT|BUSFREE jz .;
309 test SSTAT1, BUSFREE jnz poll_for_work;
310 mvi INTSTAT, BAD_PHASE;
312 clear_target_state:
313 /*
314 * We assume that the kernel driver may reset us
315 * at any time, even in the middle of a DMA, so
316 * clear DFCNTRL too.
317 */
318 clr DFCNTRL;
320 /*
321 * We don't know the target we will connect to,
322 * so default to narrow transfers to avoid
323 * parity problems.
324 */
325 if ((p->features & AHC_ULTRA2) != 0) {
326 bmov SCSIRATE, ALLZEROS, 2;
327 } else {
328 clr SCSIRATE;
329 and SXFRCTL0, ~(FAST20);
330 }
331 mvi LASTPHASE, P_BUSFREE;
332 /* clear target specific flags */
333 clr SEQ_FLAGS ret;
336 data_phase_reinit:
337 /*
338 * If we re-enter the data phase after going through another phase, the
339 * STCNT may have been cleared, so restore it from the residual field.
340 * On Ultra2, we have to put it into the HCNT field because we have to
341 * drop the data down into the shadow layer via the preload ability.
342 */
343 if ((p->features & AHC_ULTRA2) != 0) {
344 bmov HADDR, SHADDR, 4;
345 bmov HCNT, SCB_RESID_DCNT, 3;
346 }
347 if ((p->chip & AHC_CHIPID_MASK) == AHC_AIC7895) {
348 bmov STCNT, SCB_RESID_DCNT, 3;
349 }
350 if ((p->features & AHC_CMD_CHAN) == 0) {
351 mvi DINDEX, STCNT;
352 mvi SCB_RESID_DCNT call bcopy_3;
353 }
354 jmp data_phase_loop;
355 p_data:
356 if ((p->features & AHC_ULTRA2) != 0) {
357 mvi DMAPARAMS, PRELOADEN|SCSIEN|HDMAEN;
358 } else {
359 mvi DMAPARAMS, WIDEODD|SCSIEN|SDMAEN|HDMAEN|FIFORESET;
360 }
361 test LASTPHASE, IOI jnz . + 2;
362 or DMAPARAMS, DIRECTION;
363 call assert; /*
364 * Ensure entering a data
365 * phase is okay - seen identify, etc.
366 */
367 if ((p->features & AHC_CMD_CHAN) != 0) {
368 mvi CCSGADDR, CCSGADDR_MAX;
369 }
371 test SEQ_FLAGS, DPHASE jnz data_phase_reinit;
372 or SEQ_FLAGS, DPHASE; /* we've seen a data phase */
373 /*
374 * Initialize the DMA address and counter from the SCB.
375 * Also set SG_COUNT and SG_NEXT in memory since we cannot
376 * modify the values in the SCB itself until we see a
377 * save data pointers message.
378 */
379 if ((p->features & AHC_CMD_CHAN) != 0) {
380 bmov HADDR, SCB_DATAPTR, 7;
381 bmov SG_COUNT, SCB_SGCOUNT, 5;
382 if ((p->features & AHC_ULTRA2) == 0) {
383 bmov STCNT, HCNT, 3;
384 }
385 } else {
386 mvi DINDEX, HADDR;
387 mvi SCB_DATAPTR call bcopy_7;
388 call set_stcnt_from_hcnt;
389 mvi DINDEX, SG_COUNT;
390 mvi SCB_SGCOUNT call bcopy_5;
391 }
392 data_phase_loop:
393 /* Guard against overruns */
394 test SG_COUNT, 0xff jnz data_phase_inbounds;
395 /*
396 * Turn on 'Bit Bucket' mode, set the transfer count to
397 * 16meg and let the target run until it changes phase.
398 * When the transfer completes, notify the host that we
399 * had an overrun.
400 */
401 or SXFRCTL1,BITBUCKET;
402 and DMAPARAMS, ~(HDMAEN|SDMAEN);
403 if ((p->features & AHC_ULTRA2) != 0) {
404 bmov HCNT, ALLONES, 3;
405 }
406 if ((p->chip & AHC_CHIPID_MASK) == AHC_AIC7895) {
407 bmov STCNT, ALLONES, 3;
408 }
409 if ((p->features & AHC_CMD_CHAN) == 0) {
410 mvi STCNT[0], 0xFF;
411 mvi STCNT[1], 0xFF;
412 mvi STCNT[2], 0xFF;
413 }
415 data_phase_inbounds:
416 /* If we are the last SG block, tell the hardware. */
417 if ((p->features & AHC_ULTRA2) != 0) {
418 shl A, 2, SG_COUNT;
419 cmp SG_COUNT,0x01 jne data_phase_wideodd;
420 or A, LAST_SEG;
421 } else {
422 cmp SG_COUNT,0x01 jne data_phase_wideodd;
423 and DMAPARAMS, ~WIDEODD;
424 }
425 data_phase_wideodd:
426 if ((p->features & AHC_ULTRA2) != 0) {
427 mov SG_CACHEPTR, A;
428 mov DFCNTRL, DMAPARAMS; /* start the operation */
429 test SXFRCTL1, BITBUCKET jnz data_phase_overrun;
430 u2_preload_wait:
431 test SSTAT1, PHASEMIS jnz u2_phasemis;
432 test DFSTATUS, PRELOAD_AVAIL jz u2_preload_wait;
433 } else {
434 mov DMAPARAMS call dma;
435 data_phase_dma_done:
436 /* Go tell the host about any overruns */
437 test SXFRCTL1,BITBUCKET jnz data_phase_overrun;
439 /* Exit if we had an underrun. dma clears SINDEX in this case. */
440 test SINDEX,0xff jz data_phase_finish;
441 }
442 /*
443 * Advance the scatter-gather pointers
444 */
445 sg_advance:
446 if ((p->features & AHC_ULTRA2) != 0) {
447 cmp SG_COUNT, 0x01 je u2_data_phase_finish;
448 } else {
449 dec SG_COUNT;
450 test SG_COUNT, 0xff jz data_phase_finish;
451 }
453 if ((p->features & AHC_CMD_CHAN) != 0) {
455 /*
456 * Do we have any prefetch left???
457 */
458 cmp CCSGADDR, CCSGADDR_MAX jne prefetch_avail;
460 /*
461 * Fetch MIN(CCSGADDR_MAX, (SG_COUNT * 8)) bytes.
462 */
463 add A, -(CCSGRAM_MAXSEGS + 1), SG_COUNT;
464 mvi A, CCSGADDR_MAX;
465 jc . + 2;
466 shl A, 3, SG_COUNT;
467 mov CCHCNT, A;
468 bmov CCHADDR, SG_NEXT, 4;
469 mvi CCSGCTL, CCSGEN|CCSGRESET;
470 test CCSGCTL, CCSGDONE jz .;
471 and CCSGCTL, ~CCSGEN;
472 test CCSGCTL, CCSGEN jnz .;
473 mvi CCSGCTL, CCSGRESET;
474 prefetch_avail:
475 bmov HADDR, CCSGRAM, 8;
476 if ((p->features & AHC_ULTRA2) == 0) {
477 bmov STCNT, HCNT, 3;
478 } else {
479 dec SG_COUNT;
480 }
481 } else {
482 mvi DINDEX, HADDR;
483 mvi SG_NEXT call bcopy_4;
485 mvi HCNT[0],SG_SIZEOF;
486 clr HCNT[1];
487 clr HCNT[2];
489 or DFCNTRL, HDMAEN|DIRECTION|FIFORESET;
491 call dma_finish;
493 /*
494 * Copy data from FIFO into SCB data pointer and data count.
495 * This assumes that the SG segments are of the form:
496 * struct ahc_dma_seg {
497 * u_int32_t addr; four bytes, little-endian order
498 * u_int32_t len; four bytes, little endian order
499 * };
500 */
501 mvi DINDEX, HADDR;
502 call dfdat_in_7;
503 call set_stcnt_from_hcnt;
504 }
505 /* Advance the SG pointer */
506 clr A; /* add sizeof(struct scatter) */
507 add SG_NEXT[0],SG_SIZEOF;
508 adc SG_NEXT[1],A;
510 if ((p->features & AHC_ULTRA2) != 0) {
511 jmp data_phase_loop;
512 } else {
513 test SSTAT1, REQINIT jz .;
514 test SSTAT1,PHASEMIS jz data_phase_loop;
515 }
518 /*
519 * We've loaded all of our segments into the preload layer. Now, we simply
520 * have to wait for it to finish or for us to get a phasemis. And, since
521 * we'll get a phasemis if we do finish, all we really need to do is wait
522 * for a phasemis then check if we did actually complete all the segments.
523 */
524 if ((p->features & AHC_ULTRA2) != 0) {
525 u2_data_phase_finish:
526 test SSTAT1, PHASEMIS jnz u2_phasemis;
527 test SG_CACHEPTR, LAST_SEG_DONE jz u2_data_phase_finish;
528 clr SG_COUNT;
529 test SSTAT1, REQINIT jz .;
530 test SSTAT1, PHASEMIS jz data_phase_loop;
531 u2_phasemis:
532 call ultra2_dmafinish;
533 test SG_CACHEPTR, LAST_SEG_DONE jnz data_phase_finish;
534 test SSTAT2, SHVALID jnz u2_fixup_residual;
535 mvi INTSTAT, SEQ_SG_FIXUP;
536 jmp data_phase_finish;
537 u2_fixup_residual:
538 shr ARG_1, 2, SG_CACHEPTR;
539 u2_phasemis_loop:
540 and A, 0x3f, SG_COUNT;
541 cmp ARG_1, A je data_phase_finish;
542 /*
543 * Subtract SG_SIZEOF from the SG_NEXT pointer and add 1 to the SG_COUNT
544 */
545 clr A;
546 add SG_NEXT[0], -SG_SIZEOF;
547 adc SG_NEXT[1], 0xff;
548 inc SG_COUNT;
549 jmp u2_phasemis_loop;
550 }
552 data_phase_finish:
553 /*
554 * After a DMA finishes, save the SG and STCNT residuals back into the SCB
555 * We use STCNT instead of HCNT, since it's a reflection of how many bytes
556 * were transferred on the SCSI (as opposed to the host) bus.
557 */
558 if ((p->features & AHC_CMD_CHAN) != 0) {
559 bmov SCB_RESID_DCNT, STCNT, 3;
560 mov SCB_RESID_SGCNT, SG_COUNT;
561 if ((p->features & AHC_ULTRA2) != 0) {
562 or SXFRCTL0, CLRSTCNT|CLRCHN;
563 }
564 } else {
565 mov SCB_RESID_DCNT[0],STCNT[0];
566 mov SCB_RESID_DCNT[1],STCNT[1];
567 mov SCB_RESID_DCNT[2],STCNT[2];
568 mov SCB_RESID_SGCNT, SG_COUNT;
569 }
571 jmp ITloop;
573 data_phase_overrun:
574 /*
575 * Turn off BITBUCKET mode and notify the host
576 */
577 if ((p->features & AHC_ULTRA2) != 0) {
578 /*
579 * Wait for the target to quit transferring data on the SCSI bus
580 */
581 test SSTAT1, PHASEMIS jz .;
582 call ultra2_dmafinish;
583 }
584 and SXFRCTL1, ~BITBUCKET;
585 mvi INTSTAT,DATA_OVERRUN;
586 jmp ITloop;
591 /*
592 * Actually turn off the DMA hardware, save our current position into the
593 * proper residual variables, wait for the next REQ signal, then jump to
594 * the ITloop. Jumping to the ITloop ensures that if we happen to get
595 * brought into the data phase again (or are still in it after our last
596 * segment) that we will properly signal an overrun to the kernel.
597 */
598 if ((p->features & AHC_ULTRA2) != 0) {
599 ultra2_dmafinish:
600 test DFCNTRL, DIRECTION jnz ultra2_dmahalt;
601 and DFCNTRL, ~SCSIEN;
602 test DFCNTRL, SCSIEN jnz .;
603 if ((p->bugs & AHC_BUG_AUTOFLUSH) != 0) {
604 or DFCNTRL, FIFOFLUSH;
605 }
606 ultra2_dmafifoflush:
607 if ((p->bugs & AHC_BUG_AUTOFLUSH) != 0) {
608 /*
609 * hardware bug alert! This needless set of jumps
610 * works around a glitch in the silicon. When the
611 * PCI DMA fifo goes empty, but there is still SCSI
612 * data to be flushed into the PCI DMA fifo (and from
613 * there on into main memory), the FIFOEMP bit will
614 * come on between the time when the PCI DMA buffer
615 * went empty and the next bit of data is copied from
616 * the SCSI fifo into the PCI fifo. It should only
617 * come on when both FIFOs (meaning the entire FIFO
618 * chain) are empty. Since it can take up to 4 cycles
619 * for new data to be copied from the SCSI fifo into
620 * the PCI fifo, testing for FIFOEMP status for 4
621 * extra times gives the needed time for any
622 * remaining SCSI fifo data to be put in the PCI fifo
623 * before we declare it *truly* empty.
624 */
625 test DFSTATUS, FIFOEMP jz ultra2_dmafifoflush;
626 test DFSTATUS, FIFOEMP jz ultra2_dmafifoflush;
627 test DFSTATUS, FIFOEMP jz ultra2_dmafifoflush;
628 test DFSTATUS, FIFOEMP jz ultra2_dmafifoflush;
629 }
630 test DFSTATUS, FIFOEMP jz ultra2_dmafifoflush;
631 test DFSTATUS, MREQPEND jnz .;
632 ultra2_dmahalt:
633 and DFCNTRL, ~(HDMAEN|SCSIEN);
634 test DFCNTRL, (HDMAEN|SCSIEN) jnz .;
635 ret;
636 }
638 /*
639 * Command phase. Set up the DMA registers and let 'er rip.
640 */
641 p_command:
642 call assert;
644 /*
645 * Load HADDR and HCNT.
646 */
647 if ((p->features & AHC_CMD_CHAN) != 0) {
648 bmov HADDR, SCB_CMDPTR, 5;
649 bmov HCNT[1], ALLZEROS, 2;
650 if ((p->features & AHC_ULTRA2) == 0) {
651 bmov STCNT, HCNT, 3;
652 }
653 } else {
654 mvi DINDEX, HADDR;
655 mvi SCB_CMDPTR call bcopy_5;
656 clr HCNT[1];
657 clr HCNT[2];
658 call set_stcnt_from_hcnt;
659 }
661 if ((p->features & AHC_ULTRA2) == 0) {
662 mvi (SCSIEN|SDMAEN|HDMAEN|DIRECTION|FIFORESET) call dma;
663 } else {
664 mvi DFCNTRL, (PRELOADEN|SCSIEN|HDMAEN|DIRECTION);
665 test SSTAT0, SDONE jnz .;
666 p_command_dma_loop:
667 test SSTAT0, SDONE jnz p_command_ultra2_dma_done;
668 test SSTAT1,PHASEMIS jz p_command_dma_loop; /* ie. underrun */
669 p_command_ultra2_dma_done:
670 test SCSISIGI, REQI jz p_command_ultra2_shutdown;
671 test SSTAT1, (PHASEMIS|REQINIT) jz p_command_ultra2_dma_done;
672 p_command_ultra2_shutdown:
673 and DFCNTRL, ~(HDMAEN|SCSIEN);
674 test DFCNTRL, (HDMAEN|SCSIEN) jnz .;
675 or SXFRCTL0, CLRSTCNT|CLRCHN;
676 }
677 jmp ITloop;
679 /*
680 * Status phase. Wait for the data byte to appear, then read it
681 * and store it into the SCB.
682 */
683 p_status:
684 call assert;
686 mov SCB_TARGET_STATUS, SCSIDATL;
687 jmp ITloop;
689 /*
690 * Message out phase. If MSG_OUT is 0x80, build I full indentify message
691 * sequence and send it to the target. In addition, if the MK_MESSAGE bit
692 * is set in the SCB_CONTROL byte, interrupt the host and allow it to send
693 * it's own message.
694 *
695 * If MSG_OUT is == HOST_MSG, also interrupt the host and take a message.
696 * This is done to allow the hsot to send messages outside of an identify
697 * sequence while protecting the seqencer from testing the MK_MESSAGE bit
698 * on an SCB that might not be for the current nexus. (For example, a
699 * BDR message in response to a bad reselection would leave us pointed to
700 * an SCB that doesn't have anything to do with the current target).
701 * Otherwise, treat MSG_OUT as a 1 byte message to send (abort, abort tag,
702 * bus device reset).
703 *
704 * When there are no messages to send, MSG_OUT should be set to MSG_NOOP,
705 * in case the target decides to put us in this phase for some strange
706 * reason.
707 */
708 p_mesgout_retry:
709 or SCSISIGO,ATNO,LASTPHASE;/* turn on ATN for the retry */
710 p_mesgout:
711 mov SINDEX, MSG_OUT;
712 cmp SINDEX, MSG_IDENTIFYFLAG jne p_mesgout_from_host;
713 p_mesgout_identify:
714 if ((p->features & AHC_WIDE) != 0) {
715 and SINDEX,0xf,SCB_TCL; /* lun */
716 } else {
717 and SINDEX,0x7,SCB_TCL; /* lun */
718 }
719 and A,DISCENB,SCB_CONTROL; /* mask off disconnect privilege */
720 or SINDEX,A; /* or in disconnect privilege */
721 or SINDEX,MSG_IDENTIFYFLAG;
722 p_mesgout_mk_message:
723 test SCB_CONTROL,MK_MESSAGE jz p_mesgout_tag;
724 mov SCSIDATL, SINDEX; /* Send the last byte */
725 jmp p_mesgout_from_host + 1;/* Skip HOST_MSG test */
726 /*
727 * Send a tag message if TAG_ENB is set in the SCB control block.
728 * Use SCB_TAG (the position in the kernel's SCB array) as the tag value.
729 */
730 p_mesgout_tag:
731 test SCB_CONTROL,TAG_ENB jz p_mesgout_onebyte;
732 mov SCSIDATL, SINDEX; /* Send the identify message */
733 call phase_lock;
734 cmp LASTPHASE, P_MESGOUT jne p_mesgout_done;
735 and SCSIDATL,TAG_ENB|SCB_TAG_TYPE,SCB_CONTROL;
736 call phase_lock;
737 cmp LASTPHASE, P_MESGOUT jne p_mesgout_done;
738 mov SCB_TAG jmp p_mesgout_onebyte;
739 /*
740 * Interrupt the driver, and allow it to send a message
741 * if it asks.
742 */
743 p_mesgout_from_host:
744 cmp SINDEX, HOST_MSG jne p_mesgout_onebyte;
745 mvi INTSTAT,AWAITING_MSG;
746 nop;
747 /*
748 * Did the host detect a phase change?
749 */
750 cmp RETURN_1, MSGOUT_PHASEMIS je p_mesgout_done;
752 p_mesgout_onebyte:
753 mvi CLRSINT1, CLRATNO;
754 mov SCSIDATL, SINDEX;
756 /*
757 * If the next bus phase after ATN drops is a message out, it means
758 * that the target is requesting that the last message(s) be resent.
759 */
760 call phase_lock;
761 cmp LASTPHASE, P_MESGOUT je p_mesgout_retry;
763 p_mesgout_done:
764 mvi CLRSINT1,CLRATNO; /* Be sure to turn ATNO off */
765 mov LAST_MSG, MSG_OUT;
766 cmp MSG_OUT, MSG_IDENTIFYFLAG jne . + 2;
767 and SCB_CONTROL, ~MK_MESSAGE;
768 mvi MSG_OUT, MSG_NOOP; /* No message left */
769 jmp ITloop;
771 /*
772 * Message in phase. Bytes are read using Automatic PIO mode.
773 */
774 p_mesgin:
775 mvi ACCUM call inb_first; /* read the 1st message byte */
777 test A,MSG_IDENTIFYFLAG jnz mesgin_identify;
778 cmp A,MSG_DISCONNECT je mesgin_disconnect;
779 cmp A,MSG_SAVEDATAPOINTER je mesgin_sdptrs;
780 cmp ALLZEROS,A je mesgin_complete;
781 cmp A,MSG_RESTOREPOINTERS je mesgin_rdptrs;
782 cmp A,MSG_EXTENDED je mesgin_extended;
783 cmp A,MSG_MESSAGE_REJECT je mesgin_reject;
784 cmp A,MSG_NOOP je mesgin_done;
785 cmp A,MSG_IGN_WIDE_RESIDUE je mesgin_wide_residue;
787 rej_mesgin:
788 /*
789 * We have no idea what this message in is, so we issue a message reject
790 * and hope for the best. In any case, rejection should be a rare
791 * occurrence - signal the driver when it happens.
792 */
793 mvi INTSTAT,SEND_REJECT; /* let driver know */
795 mvi MSG_MESSAGE_REJECT call mk_mesg;
797 mesgin_done:
798 mov NONE,SCSIDATL; /*dummy read from latch to ACK*/
799 jmp ITloop;
802 mesgin_complete:
803 /*
804 * We got a "command complete" message, so put the SCB_TAG into the QOUTFIFO,
805 * and trigger a completion interrupt. Before doing so, check to see if there
806 * is a residual or the status byte is something other than STATUS_GOOD (0).
807 * In either of these conditions, we upload the SCB back to the host so it can
808 * process this information. In the case of a non zero status byte, we
809 * additionally interrupt the kernel driver synchronously, allowing it to
810 * decide if sense should be retrieved. If the kernel driver wishes to request
811 * sense, it will fill the kernel SCB with a request sense command and set
812 * RETURN_1 to SEND_SENSE. If RETURN_1 is set to SEND_SENSE we redownload
813 * the SCB, and process it as the next command by adding it to the waiting list.
814 * If the kernel driver does not wish to request sense, it need only clear
815 * RETURN_1, and the command is allowed to complete normally. We don't bother
816 * to post to the QOUTFIFO in the error cases since it would require extra
817 * work in the kernel driver to ensure that the entry was removed before the
818 * command complete code tried processing it.
819 */
821 /*
822 * First check for residuals
823 */
824 test SCB_RESID_SGCNT,0xff jnz upload_scb;
825 test SCB_TARGET_STATUS,0xff jz complete; /* Good Status? */
826 upload_scb:
827 mvi DMAPARAMS, FIFORESET;
828 mov SCB_TAG call dma_scb;
829 check_status:
830 test SCB_TARGET_STATUS,0xff jz complete; /* Just a residual? */
831 mvi INTSTAT,BAD_STATUS; /* let driver know */
832 nop;
833 cmp RETURN_1, SEND_SENSE jne complete;
834 /* This SCB becomes the next to execute as it will retrieve sense */
835 mvi DMAPARAMS, HDMAEN|DIRECTION|FIFORESET;
836 mov SCB_TAG call dma_scb;
837 add_to_waiting_list:
838 mov SCB_NEXT,WAITING_SCBH;
839 mov WAITING_SCBH, SCBPTR;
840 /*
841 * Prepare our selection hardware before the busfree so we have a
842 * high probability of winning arbitration.
843 */
844 call start_selection;
845 jmp await_busfree;
847 complete:
848 /* If we are untagged, clear our address up in host ram */
849 test SCB_CONTROL, TAG_ENB jnz complete_post;
850 mov A, SAVED_TCL;
851 mvi UNTAGGEDSCB_OFFSET call post_byte_setup;
852 mvi SCB_LIST_NULL call post_byte;
854 complete_post:
855 /* Post the SCB and issue an interrupt */
856 if ((p->features & AHC_QUEUE_REGS) != 0) {
857 mov A, SDSCB_QOFF;
858 } else {
859 mov A, QOUTPOS;
860 }
861 mvi QOUTFIFO_OFFSET call post_byte_setup;
862 mov SCB_TAG call post_byte;
863 if ((p->features & AHC_QUEUE_REGS) == 0) {
864 inc QOUTPOS;
865 }
866 mvi INTSTAT,CMDCMPLT;
868 add_to_free_list:
869 call add_scb_to_free_list;
870 jmp await_busfree;
872 /*
873 * Is it an extended message? Copy the message to our message buffer and
874 * notify the host. The host will tell us whether to reject this message,
875 * respond to it with the message that the host placed in our message buffer,
876 * or simply to do nothing.
877 */
878 mesgin_extended:
879 mvi INTSTAT,EXTENDED_MSG; /* let driver know */
880 jmp ITloop;
882 /*
883 * Is it a disconnect message? Set a flag in the SCB to remind us
884 * and await the bus going free.
885 */
886 mesgin_disconnect:
887 or SCB_CONTROL,DISCONNECTED;
888 call add_scb_to_disc_list;
889 jmp await_busfree;
891 /*
892 * Save data pointers message:
893 * Copying RAM values back to SCB, for Save Data Pointers message, but
894 * only if we've actually been into a data phase to change them. This
895 * protects against bogus data in scratch ram and the residual counts
896 * since they are only initialized when we go into data_in or data_out.
897 */
898 mesgin_sdptrs:
899 test SEQ_FLAGS, DPHASE jz mesgin_done;
900 /*
901 * The SCB SGPTR becomes the next one we'll download,
902 * and the SCB DATAPTR becomes the current SHADDR.
903 * Use the residual number since STCNT is corrupted by
904 * any message transfer.
905 */
906 if ((p->features & AHC_CMD_CHAN) != 0) {
907 bmov SCB_SGCOUNT, SG_COUNT, 5;
908 bmov SCB_DATAPTR, SHADDR, 4;
909 bmov SCB_DATACNT, SCB_RESID_DCNT, 3;
910 } else {
911 mvi DINDEX, SCB_SGCOUNT;
912 mvi SG_COUNT call bcopy_5;
913 mvi DINDEX, SCB_DATAPTR;
914 mvi SHADDR call bcopy_4;
915 mvi SCB_RESID_DCNT call bcopy_3;
916 }
917 jmp mesgin_done;
919 /*
920 * Restore pointers message? Data pointers are recopied from the
921 * SCB anytime we enter a data phase for the first time, so all
922 * we need to do is clear the DPHASE flag and let the data phase
923 * code do the rest.
924 */
925 mesgin_rdptrs:
926 and SEQ_FLAGS, ~DPHASE; /*
927 * We'll reload them
928 * the next time through
929 * the dataphase.
930 */
931 jmp mesgin_done;
933 /*
934 * Identify message? For a reconnecting target, this tells us the lun
935 * that the reconnection is for - find the correct SCB and switch to it,
936 * clearing the "disconnected" bit so we don't "find" it by accident later.
937 */
938 mesgin_identify:
940 if ((p->features & AHC_WIDE) != 0) {
941 and A,0x0f; /* lun in lower four bits */
942 } else {
943 and A,0x07; /* lun in lower three bits */
944 }
945 or SAVED_TCL,A; /* SAVED_TCL should be complete now */
947 mvi ARG_2, SCB_LIST_NULL; /* SCBID of prev SCB in disc List */
948 call get_untagged_SCBID;
949 cmp ARG_1, SCB_LIST_NULL je snoop_tag;
950 if ((p->flags & AHC_PAGESCBS) != 0) {
951 test SEQ_FLAGS, SCBPTR_VALID jz use_retrieveSCB;
952 }
953 /*
954 * If the SCB was found in the disconnected list (as is
955 * always the case in non-paging scenarios), SCBPTR is already
956 * set to the correct SCB. So, simply setup the SCB and get
957 * on with things.
958 */
959 mov SCBPTR call rem_scb_from_disc_list;
960 jmp setup_SCB;
961 /*
962 * Here we "snoop" the bus looking for a SIMPLE QUEUE TAG message.
963 * If we get one, we use the tag returned to find the proper
964 * SCB. With SCB paging, this requires using search for both tagged
965 * and non-tagged transactions since the SCB may exist in any slot.
966 * If we're not using SCB paging, we can use the tag as the direct
967 * index to the SCB.
968 */
969 snoop_tag:
970 mov NONE,SCSIDATL; /* ACK Identify MSG */
971 snoop_tag_loop:
972 call phase_lock;
973 cmp LASTPHASE, P_MESGIN jne not_found;
974 cmp SCSIBUSL,MSG_SIMPLE_Q_TAG jne not_found;
975 get_tag:
976 mvi ARG_1 call inb_next; /* tag value */
978 use_retrieveSCB:
979 call retrieveSCB;
980 setup_SCB:
981 mov A, SAVED_TCL;
982 cmp SCB_TCL, A jne not_found_cleanup_scb;
983 test SCB_CONTROL,DISCONNECTED jz not_found_cleanup_scb;
984 and SCB_CONTROL,~DISCONNECTED;
985 or SEQ_FLAGS,IDENTIFY_SEEN; /* make note of IDENTIFY */
986 /* See if the host wants to send a message upon reconnection */
987 test SCB_CONTROL, MK_MESSAGE jz mesgin_done;
988 and SCB_CONTROL, ~MK_MESSAGE;
989 mvi HOST_MSG call mk_mesg;
990 jmp mesgin_done;
992 not_found_cleanup_scb:
993 test SCB_CONTROL, DISCONNECTED jz . + 3;
994 call add_scb_to_disc_list;
995 jmp not_found;
996 call add_scb_to_free_list;
997 not_found:
998 mvi INTSTAT, NO_MATCH;
999 mvi MSG_BUS_DEV_RESET call mk_mesg;
1000 jmp mesgin_done;
1002 /*
1003 * Message reject? Let the kernel driver handle this. If we have an
1004 * outstanding WDTR or SDTR negotiation, assume that it's a response from
1005 * the target selecting 8bit or asynchronous transfer, otherwise just ignore
1006 * it since we have no clue what it pertains to.
1007 */
1008 mesgin_reject:
1009 mvi INTSTAT, REJECT_MSG;
1010 jmp mesgin_done;
1012 /*
1013 * Wide Residue. We handle the simple cases, but pass of the one hard case
1014 * to the kernel (when the residue byte happened to cause us to advance our
1015 * sg element array, so we know have to back that advance out).
1016 */
1017 mesgin_wide_residue:
1018 mvi ARG_1 call inb_next; /* ACK the wide_residue and get */
1019 /* the size byte */
1020 /*
1021 * In order for this to be reliable, we have to do all sorts of horrible
1022 * magic in terms of resetting the datafifo and reloading the shadow layer
1023 * with the correct new values (so that a subsequent save data pointers
1024 * message will do the right thing). We let the kernel do that work.
1025 */
1026 mvi INTSTAT, WIDE_RESIDUE;
1027 jmp mesgin_done;
1029 /*
1030 * [ ADD MORE MESSAGE HANDLING HERE ]
1031 */
1033 /*
1034 * Locking the driver out, build a one-byte message passed in SINDEX
1035 * if there is no active message already. SINDEX is returned intact.
1036 */
1037 mk_mesg:
1038 or SCSISIGO,ATNO,LASTPHASE;/* turn on ATNO */
1039 mov MSG_OUT,SINDEX ret;
1041 /*
1042 * Functions to read data in Automatic PIO mode.
1043 *
1044 * According to Adaptec's documentation, an ACK is not sent on input from
1045 * the target until SCSIDATL is read from. So we wait until SCSIDATL is
1046 * latched (the usual way), then read the data byte directly off the bus
1047 * using SCSIBUSL. When we have pulled the ATN line, or we just want to
1048 * acknowledge the byte, then we do a dummy read from SCISDATL. The SCSI
1049 * spec guarantees that the target will hold the data byte on the bus until
1050 * we send our ACK.
1051 *
1052 * The assumption here is that these are called in a particular sequence,
1053 * and that REQ is already set when inb_first is called. inb_{first,next}
1054 * use the same calling convention as inb.
1055 */
1057 inb_next:
1058 mov NONE,SCSIDATL; /*dummy read from latch to ACK*/
1059 inb_next_wait:
1060 /*
1061 * If there is a parity error, wait for the kernel to
1062 * see the interrupt and prepare our message response
1063 * before continuing.
1064 */
1065 test SSTAT1, REQINIT jz inb_next_wait;
1066 test SSTAT1, SCSIPERR jnz .;
1067 and LASTPHASE, PHASE_MASK, SCSISIGI;
1068 cmp LASTPHASE, P_MESGIN jne mesgin_phasemis;
1069 inb_first:
1070 mov DINDEX,SINDEX;
1071 mov DINDIR,SCSIBUSL ret; /*read byte directly from bus*/
1072 inb_last:
1073 mov NONE,SCSIDATL ret; /*dummy read from latch to ACK*/
1076 mesgin_phasemis:
1077 /*
1078 * We expected to receive another byte, but the target changed phase
1079 */
1080 mvi INTSTAT, MSGIN_PHASEMIS;
1081 jmp ITloop;
1083 /*
1084 * DMA data transfer. HADDR and HCNT must be loaded first, and
1085 * SINDEX should contain the value to load DFCNTRL with - 0x3d for
1086 * host->scsi, or 0x39 for scsi->host. The SCSI channel is cleared
1087 * during initialization.
1088 */
1089 if ((p->features & AHC_ULTRA2) == 0) {
1090 dma:
1091 mov DFCNTRL,SINDEX;
1092 dma_loop:
1093 test SSTAT0,DMADONE jnz dma_dmadone;
1094 test SSTAT1,PHASEMIS jz dma_loop; /* ie. underrun */
1095 dma_phasemis:
1096 test SSTAT0,SDONE jnz dma_checkfifo;
1097 mov SINDEX,ALLZEROS; /* Notify caller of phasemiss */
1099 /*
1100 * We will be "done" DMAing when the transfer count goes to zero, or
1101 * the target changes the phase (in light of this, it makes sense that
1102 * the DMA circuitry doesn't ACK when PHASEMIS is active). If we are
1103 * doing a SCSI->Host transfer, the data FIFO should be flushed auto-
1104 * magically on STCNT=0 or a phase change, so just wait for FIFO empty
1105 * status.
1106 */
1107 dma_checkfifo:
1108 test DFCNTRL,DIRECTION jnz dma_fifoempty;
1109 dma_fifoflush:
1110 test DFSTATUS,FIFOEMP jz dma_fifoflush;
1112 dma_fifoempty:
1113 /* Don't clobber an inprogress host data transfer */
1114 test DFSTATUS, MREQPEND jnz dma_fifoempty;
1115 /*
1116 * Now shut the DMA enables off and make sure that the DMA enables are
1117 * actually off first lest we get an ILLSADDR.
1118 */
1119 dma_dmadone:
1120 cmp LASTPHASE, P_COMMAND je dma_await_nreq;
1121 test SCSIRATE, 0x0f jnz dma_shutdown;
1122 dma_await_nreq:
1123 test SCSISIGI, REQI jz dma_shutdown;
1124 test SSTAT1, (PHASEMIS|REQINIT) jz dma_await_nreq;
1125 dma_shutdown:
1126 and DFCNTRL, ~(SCSIEN|SDMAEN|HDMAEN);
1127 dma_halt:
1128 /*
1129 * Some revisions of the aic7880 have a problem where, if the
1130 * data fifo is full, but the PCI input latch is not empty,
1131 * HDMAEN cannot be cleared. The fix used here is to attempt
1132 * to drain the data fifo until there is space for the input
1133 * latch to drain and HDMAEN de-asserts.
1134 */
1135 if ((p->bugs & AHC_BUG_PCI_2_1_RETRY) != 0) {
1136 mov NONE, DFDAT;
1137 }
1138 test DFCNTRL, (SCSIEN|SDMAEN|HDMAEN) jnz dma_halt;
1139 }
1140 return:
1141 ret;
1143 /*
1144 * Assert that if we've been reselected, then we've seen an IDENTIFY
1145 * message.
1146 */
1147 assert:
1148 test SEQ_FLAGS,IDENTIFY_SEEN jnz return; /* seen IDENTIFY? */
1150 mvi INTSTAT,NO_IDENT ret; /* no - tell the kernel */
1152 /*
1153 * Locate a disconnected SCB either by SAVED_TCL (ARG_1 is SCB_LIST_NULL)
1154 * or by the SCBID ARG_1. The search begins at the SCB index passed in
1155 * via SINDEX which is an SCB that must be on the disconnected list. If
1156 * the SCB cannot be found, SINDEX will be SCB_LIST_NULL, otherwise, SCBPTR
1157 * is set to the proper SCB.
1158 */
1159 findSCB:
1160 mov SCBPTR,SINDEX; /* Initialize SCBPTR */
1161 cmp ARG_1, SCB_LIST_NULL jne findSCB_by_SCBID;
1162 mov A, SAVED_TCL;
1163 mvi SCB_TCL jmp findSCB_loop; /* &SCB_TCL -> SINDEX */
1164 findSCB_by_SCBID:
1165 mov A, ARG_1; /* Tag passed in ARG_1 */
1166 mvi SCB_TAG jmp findSCB_loop; /* &SCB_TAG -> SINDEX */
1167 findSCB_next:
1168 mov ARG_2, SCBPTR;
1169 cmp SCB_NEXT, SCB_LIST_NULL je notFound;
1170 mov SCBPTR,SCB_NEXT;
1171 dec SINDEX; /* Last comparison moved us too far */
1172 findSCB_loop:
1173 cmp SINDIR, A jne findSCB_next;
1174 mov SINDEX, SCBPTR ret;
1175 notFound:
1176 mvi SINDEX, SCB_LIST_NULL ret;
1178 /*
1179 * Retrieve an SCB by SCBID first searching the disconnected list falling
1180 * back to DMA'ing the SCB down from the host. This routine assumes that
1181 * ARG_1 is the SCBID of interest and that SINDEX is the position in the
1182 * disconnected list to start the search from. If SINDEX is SCB_LIST_NULL,
1183 * we go directly to the host for the SCB.
1184 */
1185 retrieveSCB:
1186 test SEQ_FLAGS, SCBPTR_VALID jz retrieve_from_host;
1187 mov SCBPTR call findSCB; /* Continue the search */
1188 cmp SINDEX, SCB_LIST_NULL je retrieve_from_host;
1190 /*
1191 * This routine expects SINDEX to contain the index of the SCB to be
1192 * removed, SCBPTR to be pointing to that SCB, and ARG_2 to be the
1193 * SCBID of the SCB just previous to this one in the list or SCB_LIST_NULL
1194 * if it is at the head.
1195 */
1196 rem_scb_from_disc_list:
1197 /* Remove this SCB from the disconnection list */
1198 cmp ARG_2, SCB_LIST_NULL je rHead;
1199 mov DINDEX, SCB_NEXT;
1200 mov SCBPTR, ARG_2;
1201 mov SCB_NEXT, DINDEX;
1202 mov SCBPTR, SINDEX ret;
1203 rHead:
1204 mov DISCONNECTED_SCBH,SCB_NEXT ret;
1206 retrieve_from_host:
1207 /*
1208 * We didn't find it. Pull an SCB and DMA down the one we want.
1209 * We should never get here in the non-paging case.
1210 */
1211 mov ALLZEROS call get_free_or_disc_scb;
1212 mvi DMAPARAMS, HDMAEN|DIRECTION|FIFORESET;
1213 /* Jump instead of call as we want to return anyway */
1214 mov ARG_1 jmp dma_scb;
1216 /*
1217 * Determine whether a target is using tagged or non-tagged transactions
1218 * by first looking for a matching transaction based on the TCL and if
1219 * that fails, looking up this device in the host's untagged SCB array.
1220 * The TCL to search for is assumed to be in SAVED_TCL. The value is
1221 * returned in ARG_1 (SCB_LIST_NULL for tagged, SCBID for non-tagged).
1222 * The SCBPTR_VALID bit is set in SEQ_FLAGS if we found the information
1223 * in an SCB instead of having to go to the host.
1224 */
1225 get_untagged_SCBID:
1226 cmp DISCONNECTED_SCBH, SCB_LIST_NULL je get_SCBID_from_host;
1227 mvi ARG_1, SCB_LIST_NULL;
1228 mov DISCONNECTED_SCBH call findSCB;
1229 cmp SINDEX, SCB_LIST_NULL je get_SCBID_from_host;
1230 or SEQ_FLAGS, SCBPTR_VALID;/* Was in disconnected list */
1231 test SCB_CONTROL, TAG_ENB jnz . + 2;
1232 mov ARG_1, SCB_TAG ret;
1233 mvi ARG_1, SCB_LIST_NULL ret;
1235 /*
1236 * Fetch a byte from host memory given an index of (A + (256 * SINDEX))
1237 * and a base address of SCBID_ADDR. The byte is returned in RETURN_2.
1238 */
1239 fetch_byte:
1240 mov ARG_2, SINDEX;
1241 if ((p->features & AHC_CMD_CHAN) != 0) {
1242 mvi DINDEX, CCHADDR;
1243 mvi SCBID_ADDR call set_1byte_addr;
1244 mvi CCHCNT, 1;
1245 mvi CCSGCTL, CCSGEN|CCSGRESET;
1246 test CCSGCTL, CCSGDONE jz .;
1247 mvi CCSGCTL, CCSGRESET;
1248 bmov RETURN_2, CCSGRAM, 1 ret;
1249 } else {
1250 mvi DINDEX, HADDR;
1251 mvi SCBID_ADDR call set_1byte_addr;
1252 mvi HCNT[0], 1;
1253 clr HCNT[1];
1254 clr HCNT[2];
1255 mvi DFCNTRL, HDMAEN|DIRECTION|FIFORESET;
1256 call dma_finish;
1257 mov RETURN_2, DFDAT ret;
1258 }
1260 /*
1261 * Prepare the hardware to post a byte to host memory given an
1262 * index of (A + (256 * SINDEX)) and a base address of SCBID_ADDR.
1263 */
1264 post_byte_setup:
1265 mov ARG_2, SINDEX;
1266 if ((p->features & AHC_CMD_CHAN) != 0) {
1267 mvi DINDEX, CCHADDR;
1268 mvi SCBID_ADDR call set_1byte_addr;
1269 mvi CCHCNT, 1;
1270 mvi CCSCBCTL, CCSCBRESET ret;
1271 } else {
1272 mvi DINDEX, HADDR;
1273 mvi SCBID_ADDR call set_1byte_addr;
1274 mvi HCNT[0], 1;
1275 clr HCNT[1];
1276 clr HCNT[2];
1277 mvi DFCNTRL, FIFORESET ret;
1278 }
1280 post_byte:
1281 if ((p->features & AHC_CMD_CHAN) != 0) {
1282 bmov CCSCBRAM, SINDEX, 1;
1283 or CCSCBCTL, CCSCBEN|CCSCBRESET;
1284 test CCSCBCTL, CCSCBDONE jz .;
1285 clr CCSCBCTL ret;
1286 } else {
1287 mov DFDAT, SINDEX;
1288 or DFCNTRL, HDMAEN|FIFOFLUSH;
1289 jmp dma_finish;
1290 }
1292 get_SCBID_from_host:
1293 mov A, SAVED_TCL;
1294 mvi UNTAGGEDSCB_OFFSET call fetch_byte;
1295 mov RETURN_1, RETURN_2 ret;
1297 phase_lock:
1298 test SSTAT1, REQINIT jz phase_lock;
1299 test SSTAT1, SCSIPERR jnz phase_lock;
1300 and SCSISIGO, PHASE_MASK, SCSISIGI;
1301 and LASTPHASE, PHASE_MASK, SCSISIGI ret;
1303 if ((p->features & AHC_CMD_CHAN) == 0) {
1304 set_stcnt_from_hcnt:
1305 mov STCNT[0], HCNT[0];
1306 mov STCNT[1], HCNT[1];
1307 mov STCNT[2], HCNT[2] ret;
1309 bcopy_7:
1310 mov DINDIR, SINDIR;
1311 mov DINDIR, SINDIR;
1312 bcopy_5:
1313 mov DINDIR, SINDIR;
1314 bcopy_4:
1315 mov DINDIR, SINDIR;
1316 bcopy_3:
1317 mov DINDIR, SINDIR;
1318 mov DINDIR, SINDIR;
1319 mov DINDIR, SINDIR ret;
1320 }
1322 /*
1323 * Setup addr assuming that A is an index into
1324 * an array of 32byte objects, SINDEX contains
1325 * the base address of that array, and DINDEX
1326 * contains the base address of the location
1327 * to store the indexed address.
1328 */
1329 set_32byte_addr:
1330 shr ARG_2, 3, A;
1331 shl A, 5;
1332 /*
1333 * Setup addr assuming that A + (ARG_1 * 256) is an
1334 * index into an array of 1byte objects, SINDEX contains
1335 * the base address of that array, and DINDEX contains
1336 * the base address of the location to store the computed
1337 * address.
1338 */
1339 set_1byte_addr:
1340 add DINDIR, A, SINDIR;
1341 mov A, ARG_2;
1342 adc DINDIR, A, SINDIR;
1343 clr A;
1344 adc DINDIR, A, SINDIR;
1345 adc DINDIR, A, SINDIR ret;
1347 /*
1348 * Either post or fetch and SCB from host memory based on the
1349 * DIRECTION bit in DMAPARAMS. The host SCB index is in SINDEX.
1350 */
1351 dma_scb:
1352 mov A, SINDEX;
1353 if ((p->features & AHC_CMD_CHAN) != 0) {
1354 mvi DINDEX, CCHADDR;
1355 mvi HSCB_ADDR call set_32byte_addr;
1356 mov CCSCBPTR, SCBPTR;
1357 mvi CCHCNT, 32;
1358 test DMAPARAMS, DIRECTION jz dma_scb_tohost;
1359 mvi CCSCBCTL, CCARREN|CCSCBEN|CCSCBDIR|CCSCBRESET;
1360 cmp CCSCBCTL, CCSCBDONE|ARRDONE|CCARREN|CCSCBEN|CCSCBDIR jne .;
1361 jmp dma_scb_finish;
1362 dma_scb_tohost:
1363 if ((p->features & AHC_ULTRA2) == 0) {
1364 mvi CCSCBCTL, CCSCBRESET;
1365 bmov CCSCBRAM, SCB_CONTROL, 32;
1366 or CCSCBCTL, CCSCBEN|CCSCBRESET;
1367 test CCSCBCTL, CCSCBDONE jz .;
1368 }
1369 if ((p->features & AHC_ULTRA2) != 0) {
1370 if ((p->bugs & AHC_BUG_SCBCHAN_UPLOAD) != 0) {
1371 mvi CCSCBCTL, CCARREN|CCSCBRESET;
1372 cmp CCSCBCTL, ARRDONE|CCARREN jne .;
1373 mvi CCHCNT, 32;
1374 mvi CCSCBCTL, CCSCBEN|CCSCBRESET;
1375 cmp CCSCBCTL, CCSCBDONE|CCSCBEN jne .;
1376 } else {
1377 mvi CCSCBCTL, CCARREN|CCSCBEN|CCSCBRESET;
1378 cmp CCSCBCTL, CCSCBDONE|ARRDONE|CCARREN|CCSCBEN jne .;
1379 }
1380 }
1381 dma_scb_finish:
1382 clr CCSCBCTL;
1383 test CCSCBCTL, CCARREN|CCSCBEN jnz .;
1384 ret;
1385 }
1386 if ((p->features & AHC_CMD_CHAN) == 0) {
1387 mvi DINDEX, HADDR;
1388 mvi HSCB_ADDR call set_32byte_addr;
1389 mvi HCNT[0], 32;
1390 clr HCNT[1];
1391 clr HCNT[2];
1392 mov DFCNTRL, DMAPARAMS;
1393 test DMAPARAMS, DIRECTION jnz dma_scb_fromhost;
1394 /* Fill it with the SCB data */
1395 copy_scb_tofifo:
1396 mvi SINDEX, SCB_CONTROL;
1397 add A, 32, SINDEX;
1398 copy_scb_tofifo_loop:
1399 mov DFDAT,SINDIR;
1400 mov DFDAT,SINDIR;
1401 mov DFDAT,SINDIR;
1402 mov DFDAT,SINDIR;
1403 mov DFDAT,SINDIR;
1404 mov DFDAT,SINDIR;
1405 mov DFDAT,SINDIR;
1406 mov DFDAT,SINDIR;
1407 cmp SINDEX, A jne copy_scb_tofifo_loop;
1408 or DFCNTRL, HDMAEN|FIFOFLUSH;
1409 jmp dma_finish;
1410 dma_scb_fromhost:
1411 mvi DINDEX, SCB_CONTROL;
1412 if ((p->bugs & AHC_BUG_PCI_2_1_RETRY) != 0) {
1413 /*
1414 * Set the A to -24. It it hits 0, then we let
1415 * our code fall through to dfdat_in_8 to complete
1416 * the last of the copy.
1417 *
1418 * Also, things happen 8 bytes at a time in this
1419 * case, so we may need to drain the fifo at most
1420 * 3 times to keep things flowing
1421 */
1422 mvi A, -24;
1423 dma_scb_hang_fifo:
1424 /* Wait for the first bit of data to hit the fifo */
1425 test DFSTATUS, FIFOEMP jnz .;
1426 dma_scb_hang_wait:
1427 /* OK, now they've started to transfer into the fifo,
1428 * so wait for them to stop trying to transfer any
1429 * more data.
1430 */
1431 test DFSTATUS, MREQPEND jnz .;
1432 /*
1433 * OK, they started, then they stopped, now see if they
1434 * managed to complete the job before stopping. Try
1435 * it multiple times to give the chip a few cycles to
1436 * set the flag if it did complete.
1437 */
1438 test DFSTATUS, HDONE jnz dma_scb_hang_dma_done;
1439 test DFSTATUS, HDONE jnz dma_scb_hang_dma_done;
1440 test DFSTATUS, HDONE jnz dma_scb_hang_dma_done;
1441 /*
1442 * Too bad, the chip didn't complete the DMA, but there
1443 * aren't any more memory requests pending, so that
1444 * means it stopped part way through and hung. That's
1445 * our bug, so now we drain what data there is in the
1446 * fifo in order to get things going again.
1447 */
1448 dma_scb_hang_empty_fifo:
1449 call dfdat_in_8;
1450 add A, 8;
1451 add SINDEX, A, HCNT;
1452 /*
1453 * If there are another 8 bytes of data waiting in the
1454 * fifo, then the carry bit will be set as a result
1455 * of the above add command (unless A is non-negative,
1456 * in which case the carry bit won't be set).
1457 */
1458 jc dma_scb_hang_empty_fifo;
1459 /*
1460 * We've emptied the fifo now, but we wouldn't have got
1461 * here if the memory transfer hadn't stopped part way
1462 * through, so go back up to the beginning of the
1463 * loop and start over. When it succeeds in getting
1464 * all the data down, HDONE will be set and we'll
1465 * jump to the code just below here.
1466 */
1467 jmp dma_scb_hang_fifo;
1468 dma_scb_hang_dma_done:
1469 and DFCNTRL, ~HDMAEN;
1470 test DFCNTRL, HDMAEN jnz .;
1471 call dfdat_in_8;
1472 add A, 8;
1473 cmp A, 8 jne . - 2;
1474 ret;
1475 } else {
1476 call dma_finish;
1477 call dfdat_in_8;
1478 call dfdat_in_8;
1479 call dfdat_in_8;
1480 }
1481 dfdat_in_8:
1482 mov DINDIR,DFDAT;
1483 dfdat_in_7:
1484 mov DINDIR,DFDAT;
1485 mov DINDIR,DFDAT;
1486 mov DINDIR,DFDAT;
1487 mov DINDIR,DFDAT;
1488 mov DINDIR,DFDAT;
1489 mov DINDIR,DFDAT;
1490 mov DINDIR,DFDAT ret;
1491 }
1494 /*
1495 * Wait for DMA from host memory to data FIFO to complete, then disable
1496 * DMA and wait for it to acknowledge that it's off.
1497 */
1498 if ((p->features & AHC_CMD_CHAN) == 0) {
1499 dma_finish:
1500 test DFSTATUS,HDONE jz dma_finish;
1501 /* Turn off DMA */
1502 and DFCNTRL, ~HDMAEN;
1503 test DFCNTRL, HDMAEN jnz .;
1504 ret;
1505 }
1507 add_scb_to_free_list:
1508 if ((p->flags & AHC_PAGESCBS) != 0) {
1509 mov SCB_NEXT, FREE_SCBH;
1510 mov FREE_SCBH, SCBPTR;
1511 }
1512 mvi SCB_TAG, SCB_LIST_NULL ret;
1514 if ((p->flags & AHC_PAGESCBS) != 0) {
1515 get_free_or_disc_scb:
1516 cmp FREE_SCBH, SCB_LIST_NULL jne dequeue_free_scb;
1517 cmp DISCONNECTED_SCBH, SCB_LIST_NULL jne dequeue_disc_scb;
1518 return_error:
1519 mvi SINDEX, SCB_LIST_NULL ret;
1520 dequeue_disc_scb:
1521 mov SCBPTR, DISCONNECTED_SCBH;
1522 dma_up_scb:
1523 mvi DMAPARAMS, FIFORESET;
1524 mov SCB_TAG call dma_scb;
1525 unlink_disc_scb:
1526 mov DISCONNECTED_SCBH, SCB_NEXT ret;
1527 dequeue_free_scb:
1528 mov SCBPTR, FREE_SCBH;
1529 mov FREE_SCBH, SCB_NEXT ret;
1530 }
1532 add_scb_to_disc_list:
1533 /*
1534 * Link this SCB into the DISCONNECTED list. This list holds the
1535 * candidates for paging out an SCB if one is needed for a new command.
1536 * Modifying the disconnected list is a critical(pause dissabled) section.
1537 */
1538 mov SCB_NEXT, DISCONNECTED_SCBH;
1539 mov DISCONNECTED_SCBH, SCBPTR ret;