drivers/staging/iio/accel/lis3l02dq.h

   1 /*
   2  * LISL02DQ.h -- support STMicroelectronics LISD02DQ
   3  *               3d 2g Linear Accelerometers via SPI
   4  *
   5  * Copyright (c) 2007 Jonathan Cameron <jic23@cam.ac.uk>
   6  *
   7  * Loosely based upon tle62x0.c
   8  *
   9  * This program is free software; you can redistribute it and/or modify
  10  * it under the terms of the GNU General Public License version 2 as
  11  * published by the Free Software Foundation.
  12  */
  13
  14 #ifndef SPI_LIS3L02DQ_H_
  15 #define SPI_LIS3L02DQ_H_
  16 #define LIS3L02DQ_READ_REG(a) ((a) | 0x80)
  17 #define LIS3L02DQ_WRITE_REG(a) a
  18
  19 /* Calibration parameters */
  20 #define LIS3L02DQ_REG_OFFSET_X_ADDR             0x16
  21 #define LIS3L02DQ_REG_OFFSET_Y_ADDR             0x17
  22 #define LIS3L02DQ_REG_OFFSET_Z_ADDR             0x18
  23
  24 #define LIS3L02DQ_REG_GAIN_X_ADDR               0x19
  25 #define LIS3L02DQ_REG_GAIN_Y_ADDR               0x1A
  26 #define LIS3L02DQ_REG_GAIN_Z_ADDR               0x1B
  27
  28 /* Control Register (1 of 2) */
  29 #define LIS3L02DQ_REG_CTRL_1_ADDR               0x20
  30 /* Power ctrl - either bit set corresponds to on*/
  31 #define LIS3L02DQ_REG_CTRL_1_PD_ON      0xC0
  32
  33 /* Decimation Factor  */
  34 #define LIS3L02DQ_DEC_MASK                      0x30
  35 #define LIS3L02DQ_REG_CTRL_1_DF_128             0x00
  36 #define LIS3L02DQ_REG_CTRL_1_DF_64              0x10
  37 #define LIS3L02DQ_REG_CTRL_1_DF_32              0x20
  38 #define LIS3L02DQ_REG_CTRL_1_DF_8               (0x10 | 0x20)
  39
  40 /* Self Test Enable */
  41 #define LIS3L02DQ_REG_CTRL_1_SELF_TEST_ON       0x08
  42
  43 /* Axes enable ctrls */
  44 #define LIS3L02DQ_REG_CTRL_1_AXES_Z_ENABLE      0x04
  45 #define LIS3L02DQ_REG_CTRL_1_AXES_Y_ENABLE      0x02
  46 #define LIS3L02DQ_REG_CTRL_1_AXES_X_ENABLE      0x01
  47
  48 /* Control Register (2 of 2) */
  49 #define LIS3L02DQ_REG_CTRL_2_ADDR               0x21
  50
  51 /* Block Data Update only after MSB and LSB read */
  52 #define LIS3L02DQ_REG_CTRL_2_BLOCK_UPDATE       0x40
  53
  54 /* Set to big endian output */
  55 #define LIS3L02DQ_REG_CTRL_2_BIG_ENDIAN         0x20
  56
  57 /* Reboot memory content */
  58 #define LIS3L02DQ_REG_CTRL_2_REBOOT_MEMORY      0x10
  59
  60 /* Interrupt Enable - applies data ready to the RDY pad */
  61 #define LIS3L02DQ_REG_CTRL_2_ENABLE_INTERRUPT   0x08
  62
  63 /* Enable Data Ready Generation - relationship with previous unclear in docs */
  64 #define LIS3L02DQ_REG_CTRL_2_ENABLE_DATA_READY_GENERATION 0x04
  65
  66 /* SPI 3 wire mode */
  67 #define LIS3L02DQ_REG_CTRL_2_THREE_WIRE_SPI_MODE        0x02
  68
  69 /* Data alignment, default is 12 bit right justified
  70  * - option for 16 bit left justified */
  71 #define LIS3L02DQ_REG_CTRL_2_DATA_ALIGNMENT_16_BIT_LEFT_JUSTIFIED       0x01
  72
  73 /* Interrupt related stuff */
  74 #define LIS3L02DQ_REG_WAKE_UP_CFG_ADDR                  0x23
  75
  76 /* Switch from or combination fo conditions to and */
  77 #define LIS3L02DQ_REG_WAKE_UP_CFG_BOOLEAN_AND           0x80
  78
  79 /* Latch interrupt request,
  80  * if on ack must be given by reading the ack register */
  81 #define LIS3L02DQ_REG_WAKE_UP_CFG_LATCH_SRC             0x40
  82
  83 /* Z Interrupt on High (above threshold)*/
  84 #define LIS3L02DQ_REG_WAKE_UP_CFG_INTERRUPT_Z_HIGH      0x20
  85 /* Z Interrupt on Low */
  86 #define LIS3L02DQ_REG_WAKE_UP_CFG_INTERRUPT_Z_LOW       0x10
  87 /* Y Interrupt on High */
  88 #define LIS3L02DQ_REG_WAKE_UP_CFG_INTERRUPT_Y_HIGH      0x08
  89 /* Y Interrupt on Low */
  90 #define LIS3L02DQ_REG_WAKE_UP_CFG_INTERRUPT_Y_LOW       0x04
  91 /* X Interrupt on High */
  92 #define LIS3L02DQ_REG_WAKE_UP_CFG_INTERRUPT_X_HIGH      0x02
  93 /* X Interrupt on Low */
  94 #define LIS3L02DQ_REG_WAKE_UP_CFG_INTERRUPT_X_LOW 0x01
  95
  96 /* Register that gives description of what caused interrupt
  97  * - latched if set in CFG_ADDRES */
  98 #define LIS3L02DQ_REG_WAKE_UP_SRC_ADDR                  0x24
  99 /* top bit ignored */
 100 /* Interrupt Active */
 101 #define LIS3L02DQ_REG_WAKE_UP_SRC_INTERRUPT_ACTIVATED   0x40
 102 /* Interupts that have been triggered */
 103 #define LIS3L02DQ_REG_WAKE_UP_SRC_INTERRUPT_Z_HIGH      0x20
 104 #define LIS3L02DQ_REG_WAKE_UP_SRC_INTERRUPT_Z_LOW       0x10
 105 #define LIS3L02DQ_REG_WAKE_UP_SRC_INTERRUPT_Y_HIGH      0x08
 106 #define LIS3L02DQ_REG_WAKE_UP_SRC_INTERRUPT_Y_LOW       0x04
 107 #define LIS3L02DQ_REG_WAKE_UP_SRC_INTERRUPT_X_HIGH      0x02
 108 #define LIS3L02DQ_REG_WAKE_UP_SRC_INTERRUPT_X_LOW       0x01
 109
 110 #define LIS3L02DQ_REG_WAKE_UP_ACK_ADDR                  0x25
 111
 112 /* Status register */
 113 #define LIS3L02DQ_REG_STATUS_ADDR                       0x27
 114 /* XYZ axis data overrun - first is all overrun? */
 115 #define LIS3L02DQ_REG_STATUS_XYZ_OVERRUN                0x80
 116 #define LIS3L02DQ_REG_STATUS_Z_OVERRUN                  0x40
 117 #define LIS3L02DQ_REG_STATUS_Y_OVERRUN                  0x20
 118 #define LIS3L02DQ_REG_STATUS_X_OVERRUN                  0x10
 119 /* XYZ new data available - first is all 3 available? */
 120 #define LIS3L02DQ_REG_STATUS_XYZ_NEW_DATA 0x08
 121 #define LIS3L02DQ_REG_STATUS_Z_NEW_DATA                 0x04
 122 #define LIS3L02DQ_REG_STATUS_Y_NEW_DATA                 0x02
 123 #define LIS3L02DQ_REG_STATUS_X_NEW_DATA                 0x01
 124
 125 /* The accelerometer readings - low and high bytes.
 126 Form of high byte dependent on justification set in ctrl reg */
 127 #define LIS3L02DQ_REG_OUT_X_L_ADDR                      0x28
 128 #define LIS3L02DQ_REG_OUT_X_H_ADDR                      0x29
 129 #define LIS3L02DQ_REG_OUT_Y_L_ADDR                      0x2A
 130 #define LIS3L02DQ_REG_OUT_Y_H_ADDR                      0x2B
 131 #define LIS3L02DQ_REG_OUT_Z_L_ADDR                      0x2C
 132 #define LIS3L02DQ_REG_OUT_Z_H_ADDR                      0x2D
 133
 134 /* Threshold values for all axes and both above and below thresholds
 135  * - i.e. there is only one value */
 136 #define LIS3L02DQ_REG_THS_L_ADDR                        0x2E
 137 #define LIS3L02DQ_REG_THS_H_ADDR                        0x2F
 138
 139 #define LIS3L02DQ_DEFAULT_CTRL1 (LIS3L02DQ_REG_CTRL_1_PD_ON           \
 140                                  | LIS3L02DQ_REG_CTRL_1_AXES_Z_ENABLE \
 141                                  | LIS3L02DQ_REG_CTRL_1_AXES_Y_ENABLE \
 142                                  | LIS3L02DQ_REG_CTRL_1_AXES_X_ENABLE \
 143                                  | LIS3L02DQ_REG_CTRL_1_DF_128)
 144
 145 #define LIS3L02DQ_DEFAULT_CTRL2 0
 146
 147 #define LIS3L02DQ_MAX_TX 12
 148 #define LIS3L02DQ_MAX_RX 12
 149 /**
 150  * struct lis3l02dq_state - device instance specific data
 151  * @us:                 actual spi_device
 152  * @trig:               data ready trigger registered with iio
 153  * @tx:                 transmit buffer
 154  * @rx:                 receive buffer
 155  * @buf_lock:           mutex to protect tx and rx
 156  **/
 157 struct lis3l02dq_state {
 158         struct spi_device               *us;
 159         struct iio_trigger              *trig;
 160         struct mutex                    buf_lock;
 161         bool                            trigger_on;
 162
 163         u8      tx[LIS3L02DQ_MAX_RX] ____cacheline_aligned;
 164         u8      rx[LIS3L02DQ_MAX_RX] ____cacheline_aligned;
 165 };
 166
 167 int lis3l02dq_spi_read_reg_8(struct iio_dev *indio_dev,
 168                              u8 reg_address,
 169                              u8 *val);
 170
 171 int lis3l02dq_spi_write_reg_8(struct iio_dev *indio_dev,
 172                               u8 reg_address,
 173                               u8 val);
 174
 175 int lis3l02dq_disable_all_events(struct iio_dev *indio_dev);
 176
 177 #ifdef CONFIG_IIO_BUFFER
 178 /* At the moment triggers are only used for buffer
 179  * filling. This may change!
 180  */
 181 void lis3l02dq_remove_trigger(struct iio_dev *indio_dev);
 182 int lis3l02dq_probe_trigger(struct iio_dev *indio_dev);
 183
 184 int lis3l02dq_configure_buffer(struct iio_dev *indio_dev);
 185 void lis3l02dq_unconfigure_buffer(struct iio_dev *indio_dev);
 186
 187 #ifdef CONFIG_LIS3L02DQ_BUF_RING_SW
 188 #define lis3l02dq_free_buf iio_sw_rb_free
 189 #define lis3l02dq_alloc_buf iio_sw_rb_allocate
 190 #define lis3l02dq_access_funcs ring_sw_access_funcs
 191 #endif
 192 #ifdef CONFIG_LIS3L02DQ_BUF_KFIFO
 193 #define lis3l02dq_free_buf iio_kfifo_free
 194 #define lis3l02dq_alloc_buf iio_kfifo_allocate
 195 #define lis3l02dq_access_funcs kfifo_access_funcs
 196 #endif
 197 irqreturn_t lis3l02dq_data_rdy_trig_poll(int irq, void *private);
 198 #define lis3l02dq_th lis3l02dq_data_rdy_trig_poll
 199
 200 #else /* CONFIG_IIO_BUFFER */
 201 #define lis3l02dq_th lis3l02dq_nobuffer
 202
 203 static inline void lis3l02dq_remove_trigger(struct iio_dev *indio_dev)
 204 {
 205 }
 206 static inline int lis3l02dq_probe_trigger(struct iio_dev *indio_dev)
 207 {
 208         return 0;
 209 }
 210
 211 static int lis3l02dq_configure_buffer(struct iio_dev *indio_dev)
 212 {
 213         return 0;
 214 }
 215 static inline void lis3l02dq_unconfigure_buffer(struct iio_dev *indio_dev)
 216 {
 217 }
 218 #endif /* CONFIG_IIO_BUFFER */
 219 #endif /* SPI_LIS3L02DQ_H_ */