1 chip soc
/intel
/apollolake
4 # Refer
to EDS
-Vol2
-16.32.
5 #
[14:8] steps of delay
for DDR mode
, each
125ps.
6 #
[6:0] steps of delay
for SDR mode
, each
125ps.
7 register
"emmc_tx_cmd_cntl" = "0x505"
10 # Refer
to EDS
-Vol2
-16.33.
11 #
[14:8] steps of delay
for HS400
, each
125ps.
12 #
[6:0] steps of delay
for SDR104
/HS200
, each
125ps.
13 register
"emmc_tx_data_cntl1" = "0x0b0d"
15 # EMMC TX DATA Delay
2
16 # Refer
to EDS
-Vol2
-16.34.
17 #
[30:24] steps of delay
for SDR50
, each
125ps.
18 #
[22:16] steps of delay
for DDR50
, each
125ps.
19 #
[14:8] steps of delay
for SDR25
/HS50
, each
125ps.
20 #
[6:0] steps of delay
for SDR12
, each
125ps.
21 register
"emmc_tx_data_cntl2" = "0x1c2a2a2a"
23 # EMMC RX CMD
/DATA Delay
1
24 # Refer
to EDS
-Vol2
-16.35.
25 #
[30:24] steps of delay
for SDR50
, each
125ps.
26 #
[22:16] steps of delay
for DDR50
, each
125ps.
27 #
[14:8] steps of delay
for SDR25
/HS50
, each
125ps.
28 #
[6:0] steps of delay
for SDR12
, each
125ps.
29 register
"emmc_rx_cmd_data_cntl1" = "0x00171a1a"
31 # EMMC RX CMD
/DATA Delay
2
32 # Refer
to EDS
-Vol2
-16.37.
33 #
[17:16] stands
for Rx Clock before Output Buffer
34 #
[14:8] steps of delay
for Auto Tuning Mode
, each
125ps.
35 #
[6:0] steps of delay
for HS200
, each
125ps.
36 register
"emmc_rx_cmd_data_cntl2" = "0x10028"
38 # EMMC Rx Strobe Delay
39 # Refer
to EDS
-Vol2
-16.36.
40 #
[14:8] Rx Strobe Delay DLL
1(HS400 Mode
), each
125ps.
41 #
[6:0] Rx Strobe Delay DLL
2(HS400 Mode
), each
125ps.
42 register
"emmc_rx_strobe_cntl" = "0x0b0b"
44 # Intel Common SoC Config
45 #
+-------------------+---------------------------+
47 #
+-------------------+---------------------------+
48 #| GSPI0 | cr50 TPM. Early init is |
49 #| | required
to set up a BAR |
50 #| |
for TPM communication |
51 #| | before memory is up |
54 #| I2C7 | Touchscreen |
55 #
+-------------------+---------------------------+
57 register
"tcc_offset" = "10"
59 register
"common_soc_config" = "{
65 .speed = I2C_SPEED_FAST,
70 .speed = I2C_SPEED_FAST,
73 .data_hold_time_ns = 350,
76 .speed = I2C_SPEED_FAST,
84 device pci
16.0 off
end #
- I2C
0
86 chip drivers
/i2c
/da7219
87 register
"irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_137_IRQ)"
88 register
"btn_cfg" = "50"
89 register
"mic_det_thr" = "200"
90 register
"jack_ins_deb" = "20"
91 register
"jack_det_rate" = ""32ms_64ms
""
92 register
"jack_rem_deb" = "1"
93 register
"a_d_btn_thr" = "0xa"
94 register
"d_b_btn_thr" = "0x16"
95 register
"b_c_btn_thr" = "0x21"
96 register
"c_mic_btn_thr" = "0x3e"
97 register
"btn_avg" = "4"
98 register
"adc_1bit_rpt" = "1"
99 register
"micbias_lvl" = "2600"
100 register
"mic_amp_in_sel" = ""diff
""
103 chip drivers
/i2c
/generic
104 register
"hid" = ""10EC5682
""
105 register
"name" = ""RT58
""
106 register
"desc" = ""Realtek RT5682
""
107 register
"irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_137_IRQ)"
108 register
"probed" = "1"
109 register
"property_count" = "1"
110 #
Set the jd_src
to RT5668_JD1
for jack detection
111 register
"property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
112 register
"property_list[0].name" = ""realtek
,jd
-src
""
113 register
"property_list[0].integer" = "1"
118 chip drivers
/i2c
/generic
119 register
"hid" = ""ELAN0000
""
120 register
"desc" = ""ELAN Touchpad
""
121 register
"irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPIO_135_IRQ)"
122 register
"wake" = "GPE0_DW3_27"
123 register
"detect" = "1"
128 chip drivers
/i2c
/generic
129 register
"hid" = ""ELAN0001
""
130 register
"desc" = ""ELAN Touchscreen
""
131 register
"irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_212_IRQ)"
132 register
"detect" = "1"
133 register
"reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_105)"
134 register
"reset_delay_ms" = "20"
135 register
"enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_146)"
136 register
"enable_delay_ms" = "1"
137 register
"has_power_resource" = "1"
141 register
"generic.hid" = ""GDIX0000
""
142 register
"generic.desc" = ""Goodix Touchscreen
""
143 register
"generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_212_IRQ)"
144 register
"generic.detect" = "1"
145 register
"generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_105)"
146 register
"generic.reset_delay_ms" = "120"
147 register
"generic.reset_off_delay_ms" = "3"
148 register
"generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_146)"
149 register
"generic.has_power_resource" = "1"
150 register
"generic.enable_delay_ms" = "10"
151 register
"hid_desc_reg_offset" = "0x01"
155 register
"generic.hid" = ""GTCH7503
""
156 register
"generic.desc" = ""G2TOUCH Touchscreen
""
157 register
"generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_212_IRQ)"
158 register
"generic.detect" = "1"
159 register
"generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_105)"
160 register
"generic.reset_delay_ms" = "50"
161 register
"generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_146)"
162 register
"generic.enable_delay_ms" = "1"
163 register
"generic.has_power_resource" = "1"
164 register
"hid_desc_reg_offset" = "0x01"
170 # Disable compliance mode
171 register
"disable_compliance_mode" = "1"