OMAP3: PM: Ensure MUSB block can idle when driver not loaded
[linux-ginger.git] / arch / blackfin / mach-common / arch_checks.c
blob80d39b2f9db295d2709574664528a9c71b6ac1db
1 /*
2 * File: arch/blackfin/mach-common/arch_checks.c
3 * Based on:
4 * Author: Robin Getz <rgetz@blackfin.uclinux.org>
6 * Created: 25Jul07
7 * Description: Do some checking to make sure things are OK
9 * Modified:
10 * Copyright 2004-2007 Analog Devices Inc.
12 * Bugs: Enter bugs at http://blackfin.uclinux.org/
14 * This program is free software; you can redistribute it and/or modify
15 * it under the terms of the GNU General Public License as published by
16 * the Free Software Foundation; either version 2 of the License, or
17 * (at your option) any later version.
19 * This program is distributed in the hope that it will be useful,
20 * but WITHOUT ANY WARRANTY; without even the implied warranty of
21 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
22 * GNU General Public License for more details.
24 * You should have received a copy of the GNU General Public License
25 * along with this program; if not, see the file COPYING, or write
26 * to the Free Software Foundation, Inc.,
27 * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
30 #include <asm/fixed_code.h>
31 #include <mach/anomaly.h>
32 #include <asm/clocks.h>
34 #ifdef CONFIG_BFIN_KERNEL_CLOCK
36 # if (CONFIG_VCO_HZ > CONFIG_MAX_VCO_HZ)
37 # error "VCO selected is more than maximum value. Please change the VCO multipler"
38 # endif
40 # if (CONFIG_SCLK_HZ > CONFIG_MAX_SCLK_HZ)
41 # error "Sclk value selected is more than maximum. Please select a proper value for SCLK multiplier"
42 # endif
44 # if (CONFIG_SCLK_HZ < CONFIG_MIN_SCLK_HZ)
45 # error "Sclk value selected is less than minimum. Please select a proper value for SCLK multiplier"
46 # endif
48 # if (ANOMALY_05000273) && (CONFIG_SCLK_HZ * 2 > CONFIG_CCLK_HZ)
49 # error "ANOMALY 05000273, please make sure CCLK is at least 2x SCLK"
50 # endif
52 # if (CONFIG_SCLK_HZ > CONFIG_CCLK_HZ) && (CONFIG_SCLK_HZ != CONFIG_CLKIN_HZ) && (CONFIG_CCLK_HZ != CONFIG_CLKIN_HZ)
53 # error "Please select sclk less than cclk"
54 # endif
56 #endif /* CONFIG_BFIN_KERNEL_CLOCK */
58 #if CONFIG_BOOT_LOAD < FIXED_CODE_END
59 # error "The kernel load address must be after the fixed code section"
60 #endif
62 #if (CONFIG_BOOT_LOAD & 0x3)
63 # error "The kernel load address must be 4 byte aligned"
64 #endif
66 /* The entire kernel must be able to make a 24bit pcrel call to start of L1 */
67 #if ((0xffffffff - L1_CODE_START + 1) + CONFIG_BOOT_LOAD) > 0x1000000
68 # error "The kernel load address is too high; keep it below 10meg for safety"
69 #endif
71 #if ANOMALY_05000448
72 # error You are using a part with anomaly 05000448, this issue causes random memory read/write failures - that means random crashes.
73 #endif