Documentation/devicetree/bindings/display/arm,pl11x.txt

   1 * ARM PrimeCell Color LCD Controller PL110/PL111
   2
   3 See also Documentation/devicetree/bindings/arm/primecell.txt
   4
   5 Required properties:
   6
   7 - compatible: must be one of:
   8         "arm,pl110", "arm,primecell"
   9         "arm,pl111", "arm,primecell"
  10
  11 - reg: base address and size of the control registers block
  12
  13 - interrupt-names: either the single entry "combined" representing a
  14         combined interrupt output (CLCDINTR), or the four entries
  15         "mbe", "vcomp", "lnbu", "fuf" representing the individual
  16         CLCDMBEINTR, CLCDVCOMPINTR, CLCDLNBUINTR, CLCDFUFINTR interrupts
  17
  18 - interrupts: contains an interrupt specifier for each entry in
  19         interrupt-names
  20
  21 - clock-names: should contain "clcdclk" and "apb_pclk"
  22
  23 - clocks: contains phandle and clock specifier pairs for the entries
  24         in the clock-names property. See
  25         Documentation/devicetree/binding/clock/clock-bindings.txt
  26
  27 Optional properties:
  28
  29 - memory-region: phandle to a node describing memory (see
  30         Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt)
  31         to be used for the framebuffer; if not present, the framebuffer
  32         may be located anywhere in the memory
  33
  34 - max-memory-bandwidth: maximum bandwidth in bytes per second that the
  35         cell's memory interface can handle; if not present, the memory
  36         interface is fast enough to handle all possible video modes
  37
  38 Required sub-nodes:
  39
  40 - port: describes LCD panel signals, following the common binding
  41         for video transmitter interfaces; see
  42         Documentation/devicetree/bindings/media/video-interfaces.txt;
  43         when it is a TFT panel, the port's endpoint must define the
  44         following property:
  45
  46         - arm,pl11x,tft-r0g0b0-pads: an array of three 32-bit values,
  47                 defining the way CLD pads are wired up; first value
  48                 contains index of the "CLD" external pin (pad) used
  49                 as R0 (first bit of the red component), second value
  50                 index of the pad used as G0, third value index of the
  51                 pad used as B0, see also "LCD panel signal multiplexing
  52                 details" paragraphs in the PL110/PL111 Technical
  53                 Reference Manuals; this implicitly defines available
  54                 color modes, for example:
  55                 - PL111 TFT 4:4:4 panel:
  56                         arm,pl11x,tft-r0g0b0-pads = <4 15 20>;
  57                 - PL110 TFT (1:)5:5:5 panel:
  58                         arm,pl11x,tft-r0g0b0-pads = <1 7 13>;
  59                 - PL111 TFT (1:)5:5:5 panel:
  60                         arm,pl11x,tft-r0g0b0-pads = <3 11 19>;
  61                 - PL111 TFT 5:6:5 panel:
  62                         arm,pl11x,tft-r0g0b0-pads = <3 10 19>;
  63                 - PL110 and PL111 TFT 8:8:8 panel:
  64                         arm,pl11x,tft-r0g0b0-pads = <0 8 16>;
  65                 - PL110 and PL111 TFT 8:8:8 panel, R & B components swapped:
  66                         arm,pl11x,tft-r0g0b0-pads = <16 8 0>;
  67
  68
  69 Example:
  70
  71         clcd@10020000 {
  72                 compatible = "arm,pl111", "arm,primecell";
  73                 reg = <0x10020000 0x1000>;
  74                 interrupt-names = "combined";
  75                 interrupts = <0 44 4>;
  76                 clocks = <&oscclk1>, <&oscclk2>;
  77                 clock-names = "clcdclk", "apb_pclk";
  78                 max-memory-bandwidth = <94371840>; /* Bps, 1024x768@60 16bpp */
  79
  80                 port {
  81                         clcd_pads: endpoint {
  82                                 remote-endpoint = <&clcd_panel>;
  83                                 arm,pl11x,tft-r0g0b0-pads = <0 8 16>;
  84                         };
  85                 };
  86
  87         };
  88
  89         panel {
  90                 compatible = "panel-dpi";
  91
  92                 port {
  93                         clcd_panel: endpoint {
  94                                 remote-endpoint = <&clcd_pads>;
  95                         };
  96                 };
  97
  98                 panel-timing {
  99                         clock-frequency = <25175000>;
 100                         hactive = <640>;
 101                         hback-porch = <40>;
 102                         hfront-porch = <24>;
 103                         hsync-len = <96>;
 104                         vactive = <480>;
 105                         vback-porch = <32>;
 106                         vfront-porch = <11>;
 107                         vsync-len = <2>;
 108                 };
 109         };