drivers/usb/musb/am35x.c

   1 /*
   2  * Texas Instruments AM35x "glue layer"
   3  *
   4  * Copyright (c) 2010, by Texas Instruments
   5  *
   6  * Based on the DA8xx "glue layer" code.
   7  * Copyright (c) 2008-2009, MontaVista Software, Inc. <source@mvista.com>
   8  *
   9  * This file is part of the Inventra Controller Driver for Linux.
  10  *
  11  * The Inventra Controller Driver for Linux is free software; you
  12  * can redistribute it and/or modify it under the terms of the GNU
  13  * General Public License version 2 as published by the Free Software
  14  * Foundation.
  15  *
  16  * The Inventra Controller Driver for Linux is distributed in
  17  * the hope that it will be useful, but WITHOUT ANY WARRANTY;
  18  * without even the implied warranty of MERCHANTABILITY or
  19  * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public
  20  * License for more details.
  21  *
  22  * You should have received a copy of the GNU General Public License
  23  * along with The Inventra Controller Driver for Linux ; if not,
  24  * write to the Free Software Foundation, Inc., 59 Temple Place,
  25  * Suite 330, Boston, MA  02111-1307  USA
  26  *
  27  */
  28
  29 #include <linux/init.h>
  30 #include <linux/clk.h>
  31 #include <linux/io.h>
  32 #include <linux/platform_device.h>
  33 #include <linux/dma-mapping.h>
  34
  35 #include <plat/usb.h>
  36
  37 #include "musb_core.h"
  38
  39 /*
  40  * AM35x specific definitions
  41  */
  42 /* USB 2.0 OTG module registers */
  43 #define USB_REVISION_REG        0x00
  44 #define USB_CTRL_REG            0x04
  45 #define USB_STAT_REG            0x08
  46 #define USB_EMULATION_REG       0x0c
  47 /* 0x10 Reserved */
  48 #define USB_AUTOREQ_REG         0x14
  49 #define USB_SRP_FIX_TIME_REG    0x18
  50 #define USB_TEARDOWN_REG        0x1c
  51 #define EP_INTR_SRC_REG         0x20
  52 #define EP_INTR_SRC_SET_REG     0x24
  53 #define EP_INTR_SRC_CLEAR_REG   0x28
  54 #define EP_INTR_MASK_REG        0x2c
  55 #define EP_INTR_MASK_SET_REG    0x30
  56 #define EP_INTR_MASK_CLEAR_REG  0x34
  57 #define EP_INTR_SRC_MASKED_REG  0x38
  58 #define CORE_INTR_SRC_REG       0x40
  59 #define CORE_INTR_SRC_SET_REG   0x44
  60 #define CORE_INTR_SRC_CLEAR_REG 0x48
  61 #define CORE_INTR_MASK_REG      0x4c
  62 #define CORE_INTR_MASK_SET_REG  0x50
  63 #define CORE_INTR_MASK_CLEAR_REG 0x54
  64 #define CORE_INTR_SRC_MASKED_REG 0x58
  65 /* 0x5c Reserved */
  66 #define USB_END_OF_INTR_REG     0x60
  67
  68 /* Control register bits */
  69 #define AM35X_SOFT_RESET_MASK   1
  70
  71 /* USB interrupt register bits */
  72 #define AM35X_INTR_USB_SHIFT    16
  73 #define AM35X_INTR_USB_MASK     (0x1ff << AM35X_INTR_USB_SHIFT)
  74 #define AM35X_INTR_DRVVBUS      0x100
  75 #define AM35X_INTR_RX_SHIFT     16
  76 #define AM35X_INTR_TX_SHIFT     0
  77 #define AM35X_TX_EP_MASK        0xffff          /* EP0 + 15 Tx EPs */
  78 #define AM35X_RX_EP_MASK        0xfffe          /* 15 Rx EPs */
  79 #define AM35X_TX_INTR_MASK      (AM35X_TX_EP_MASK << AM35X_INTR_TX_SHIFT)
  80 #define AM35X_RX_INTR_MASK      (AM35X_RX_EP_MASK << AM35X_INTR_RX_SHIFT)
  81
  82 #define USB_MENTOR_CORE_OFFSET  0x400
  83
  84 struct am35x_glue {
  85         struct device           *dev;
  86         struct platform_device  *musb;
  87         struct clk              *phy_clk;
  88         struct clk              *clk;
  89 };
  90 #define glue_to_musb(g)         platform_get_drvdata(g->musb)
  91
  92 /*
  93  * am35x_musb_enable - enable interrupts
  94  */
  95 static void am35x_musb_enable(struct musb *musb)
  96 {
  97         void __iomem *reg_base = musb->ctrl_base;
  98         u32 epmask;
  99
 100         /* Workaround: setup IRQs through both register sets. */
 101         epmask = ((musb->epmask & AM35X_TX_EP_MASK) << AM35X_INTR_TX_SHIFT) |
 102                ((musb->epmask & AM35X_RX_EP_MASK) << AM35X_INTR_RX_SHIFT);
 103
 104         musb_writel(reg_base, EP_INTR_MASK_SET_REG, epmask);
 105         musb_writel(reg_base, CORE_INTR_MASK_SET_REG, AM35X_INTR_USB_MASK);
 106
 107         /* Force the DRVVBUS IRQ so we can start polling for ID change. */
 108         if (is_otg_enabled(musb))
 109                 musb_writel(reg_base, CORE_INTR_SRC_SET_REG,
 110                             AM35X_INTR_DRVVBUS << AM35X_INTR_USB_SHIFT);
 111 }
 112
 113 /*
 114  * am35x_musb_disable - disable HDRC and flush interrupts
 115  */
 116 static void am35x_musb_disable(struct musb *musb)
 117 {
 118         void __iomem *reg_base = musb->ctrl_base;
 119
 120         musb_writel(reg_base, CORE_INTR_MASK_CLEAR_REG, AM35X_INTR_USB_MASK);
 121         musb_writel(reg_base, EP_INTR_MASK_CLEAR_REG,
 122                          AM35X_TX_INTR_MASK | AM35X_RX_INTR_MASK);
 123         musb_writeb(musb->mregs, MUSB_DEVCTL, 0);
 124         musb_writel(reg_base, USB_END_OF_INTR_REG, 0);
 125 }
 126
 127 #ifdef CONFIG_USB_MUSB_HDRC_HCD
 128 #define portstate(stmt)         stmt
 129 #else
 130 #define portstate(stmt)
 131 #endif
 132
 133 static void am35x_musb_set_vbus(struct musb *musb, int is_on)
 134 {
 135         WARN_ON(is_on && is_peripheral_active(musb));
 136 }
 137
 138 #define POLL_SECONDS    2
 139
 140 static struct timer_list otg_workaround;
 141
 142 static void otg_timer(unsigned long _musb)
 143 {
 144         struct musb             *musb = (void *)_musb;
 145         void __iomem            *mregs = musb->mregs;
 146         u8                      devctl;
 147         unsigned long           flags;
 148
 149         /*
 150          * We poll because AM35x's won't expose several OTG-critical
 151          * status change events (from the transceiver) otherwise.
 152          */
 153         devctl = musb_readb(mregs, MUSB_DEVCTL);
 154         DBG(7, "Poll devctl %02x (%s)\n", devctl, otg_state_string(musb));
 155
 156         spin_lock_irqsave(&musb->lock, flags);
 157         switch (musb->xceiv->state) {
 158         case OTG_STATE_A_WAIT_BCON:
 159                 devctl &= ~MUSB_DEVCTL_SESSION;
 160                 musb_writeb(musb->mregs, MUSB_DEVCTL, devctl);
 161
 162                 devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
 163                 if (devctl & MUSB_DEVCTL_BDEVICE) {
 164                         musb->xceiv->state = OTG_STATE_B_IDLE;
 165                         MUSB_DEV_MODE(musb);
 166                 } else {
 167                         musb->xceiv->state = OTG_STATE_A_IDLE;
 168                         MUSB_HST_MODE(musb);
 169                 }
 170                 break;
 171         case OTG_STATE_A_WAIT_VFALL:
 172                 musb->xceiv->state = OTG_STATE_A_WAIT_VRISE;
 173                 musb_writel(musb->ctrl_base, CORE_INTR_SRC_SET_REG,
 174                             MUSB_INTR_VBUSERROR << AM35X_INTR_USB_SHIFT);
 175                 break;
 176         case OTG_STATE_B_IDLE:
 177                 if (!is_peripheral_enabled(musb))
 178                         break;
 179
 180                 devctl = musb_readb(mregs, MUSB_DEVCTL);
 181                 if (devctl & MUSB_DEVCTL_BDEVICE)
 182                         mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ);
 183                 else
 184                         musb->xceiv->state = OTG_STATE_A_IDLE;
 185                 break;
 186         default:
 187                 break;
 188         }
 189         spin_unlock_irqrestore(&musb->lock, flags);
 190 }
 191
 192 static void am35x_musb_try_idle(struct musb *musb, unsigned long timeout)
 193 {
 194         static unsigned long last_timer;
 195
 196         if (!is_otg_enabled(musb))
 197                 return;
 198
 199         if (timeout == 0)
 200                 timeout = jiffies + msecs_to_jiffies(3);
 201
 202         /* Never idle if active, or when VBUS timeout is not set as host */
 203         if (musb->is_active || (musb->a_wait_bcon == 0 &&
 204                                 musb->xceiv->state == OTG_STATE_A_WAIT_BCON)) {
 205                 DBG(4, "%s active, deleting timer\n", otg_state_string(musb));
 206                 del_timer(&otg_workaround);
 207                 last_timer = jiffies;
 208                 return;
 209         }
 210
 211         if (time_after(last_timer, timeout) && timer_pending(&otg_workaround)) {
 212                 DBG(4, "Longer idle timer already pending, ignoring...\n");
 213                 return;
 214         }
 215         last_timer = timeout;
 216
 217         DBG(4, "%s inactive, starting idle timer for %u ms\n",
 218             otg_state_string(musb), jiffies_to_msecs(timeout - jiffies));
 219         mod_timer(&otg_workaround, timeout);
 220 }
 221
 222 static irqreturn_t am35x_musb_interrupt(int irq, void *hci)
 223 {
 224         struct musb  *musb = hci;
 225         void __iomem *reg_base = musb->ctrl_base;
 226         struct device *dev = musb->controller;
 227         struct musb_hdrc_platform_data *plat = dev->platform_data;
 228         struct omap_musb_board_data *data = plat->board_data;
 229         unsigned long flags;
 230         irqreturn_t ret = IRQ_NONE;
 231         u32 epintr, usbintr;
 232
 233         spin_lock_irqsave(&musb->lock, flags);
 234
 235         /* Get endpoint interrupts */
 236         epintr = musb_readl(reg_base, EP_INTR_SRC_MASKED_REG);
 237
 238         if (epintr) {
 239                 musb_writel(reg_base, EP_INTR_SRC_CLEAR_REG, epintr);
 240
 241                 musb->int_rx =
 242                         (epintr & AM35X_RX_INTR_MASK) >> AM35X_INTR_RX_SHIFT;
 243                 musb->int_tx =
 244                         (epintr & AM35X_TX_INTR_MASK) >> AM35X_INTR_TX_SHIFT;
 245         }
 246
 247         /* Get usb core interrupts */
 248         usbintr = musb_readl(reg_base, CORE_INTR_SRC_MASKED_REG);
 249         if (!usbintr && !epintr)
 250                 goto eoi;
 251
 252         if (usbintr) {
 253                 musb_writel(reg_base, CORE_INTR_SRC_CLEAR_REG, usbintr);
 254
 255                 musb->int_usb =
 256                         (usbintr & AM35X_INTR_USB_MASK) >> AM35X_INTR_USB_SHIFT;
 257         }
 258         /*
 259          * DRVVBUS IRQs are the only proxy we have (a very poor one!) for
 260          * AM35x's missing ID change IRQ.  We need an ID change IRQ to
 261          * switch appropriately between halves of the OTG state machine.
 262          * Managing DEVCTL.SESSION per Mentor docs requires that we know its
 263          * value but DEVCTL.BDEVICE is invalid without DEVCTL.SESSION set.
 264          * Also, DRVVBUS pulses for SRP (but not at 5V) ...
 265          */
 266         if (usbintr & (AM35X_INTR_DRVVBUS << AM35X_INTR_USB_SHIFT)) {
 267                 int drvvbus = musb_readl(reg_base, USB_STAT_REG);
 268                 void __iomem *mregs = musb->mregs;
 269                 u8 devctl = musb_readb(mregs, MUSB_DEVCTL);
 270                 int err;
 271
 272                 err = is_host_enabled(musb) && (musb->int_usb &
 273                                                 MUSB_INTR_VBUSERROR);
 274                 if (err) {
 275                         /*
 276                          * The Mentor core doesn't debounce VBUS as needed
 277                          * to cope with device connect current spikes. This
 278                          * means it's not uncommon for bus-powered devices
 279                          * to get VBUS errors during enumeration.
 280                          *
 281                          * This is a workaround, but newer RTL from Mentor
 282                          * seems to allow a better one: "re"-starting sessions
 283                          * without waiting for VBUS to stop registering in
 284                          * devctl.
 285                          */
 286                         musb->int_usb &= ~MUSB_INTR_VBUSERROR;
 287                         musb->xceiv->state = OTG_STATE_A_WAIT_VFALL;
 288                         mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ);
 289                         WARNING("VBUS error workaround (delay coming)\n");
 290                 } else if (is_host_enabled(musb) && drvvbus) {
 291                         MUSB_HST_MODE(musb);
 292                         musb->xceiv->default_a = 1;
 293                         musb->xceiv->state = OTG_STATE_A_WAIT_VRISE;
 294                         portstate(musb->port1_status |= USB_PORT_STAT_POWER);
 295                         del_timer(&otg_workaround);
 296                 } else {
 297                         musb->is_active = 0;
 298                         MUSB_DEV_MODE(musb);
 299                         musb->xceiv->default_a = 0;
 300                         musb->xceiv->state = OTG_STATE_B_IDLE;
 301                         portstate(musb->port1_status &= ~USB_PORT_STAT_POWER);
 302                 }
 303
 304                 /* NOTE: this must complete power-on within 100 ms. */
 305                 DBG(2, "VBUS %s (%s)%s, devctl %02x\n",
 306                                 drvvbus ? "on" : "off",
 307                                 otg_state_string(musb),
 308                                 err ? " ERROR" : "",
 309                                 devctl);
 310                 ret = IRQ_HANDLED;
 311         }
 312
 313         if (musb->int_tx || musb->int_rx || musb->int_usb)
 314                 ret |= musb_interrupt(musb);
 315
 316 eoi:
 317         /* EOI needs to be written for the IRQ to be re-asserted. */
 318         if (ret == IRQ_HANDLED || epintr || usbintr) {
 319                 /* clear level interrupt */
 320                 if (data->clear_irq)
 321                         data->clear_irq();
 322                 /* write EOI */
 323                 musb_writel(reg_base, USB_END_OF_INTR_REG, 0);
 324         }
 325
 326         /* Poll for ID change */
 327         if (is_otg_enabled(musb) && musb->xceiv->state == OTG_STATE_B_IDLE)
 328                 mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ);
 329
 330         spin_unlock_irqrestore(&musb->lock, flags);
 331
 332         return ret;
 333 }
 334
 335 static int am35x_musb_set_mode(struct musb *musb, u8 musb_mode)
 336 {
 337         struct device *dev = musb->controller;
 338         struct musb_hdrc_platform_data *plat = dev->platform_data;
 339         struct omap_musb_board_data *data = plat->board_data;
 340         int     retval = 0;
 341
 342         if (data->set_mode)
 343                 data->set_mode(musb_mode);
 344         else
 345                 retval = -EIO;
 346
 347         return retval;
 348 }
 349
 350 static int am35x_musb_init(struct musb *musb)
 351 {
 352         struct device *dev = musb->controller;
 353         struct musb_hdrc_platform_data *plat = dev->platform_data;
 354         struct omap_musb_board_data *data = plat->board_data;
 355         void __iomem *reg_base = musb->ctrl_base;
 356         u32 rev;
 357
 358         musb->mregs += USB_MENTOR_CORE_OFFSET;
 359
 360         /* Returns zero if e.g. not clocked */
 361         rev = musb_readl(reg_base, USB_REVISION_REG);
 362         if (!rev)
 363                 return -ENODEV;
 364
 365         usb_nop_xceiv_register();
 366         musb->xceiv = otg_get_transceiver();
 367         if (!musb->xceiv)
 368                 return -ENODEV;
 369
 370         if (is_host_enabled(musb))
 371                 setup_timer(&otg_workaround, otg_timer, (unsigned long) musb);
 372
 373         /* Reset the musb */
 374         if (data->reset)
 375                 data->reset();
 376
 377         /* Reset the controller */
 378         musb_writel(reg_base, USB_CTRL_REG, AM35X_SOFT_RESET_MASK);
 379
 380         /* Start the on-chip PHY and its PLL. */
 381         if (data->set_phy_power)
 382                 data->set_phy_power(1);
 383
 384         msleep(5);
 385
 386         musb->isr = am35x_musb_interrupt;
 387
 388         /* clear level interrupt */
 389         if (data->clear_irq)
 390                 data->clear_irq();
 391
 392         return 0;
 393 }
 394
 395 static int am35x_musb_exit(struct musb *musb)
 396 {
 397         struct device *dev = musb->controller;
 398         struct musb_hdrc_platform_data *plat = dev->platform_data;
 399         struct omap_musb_board_data *data = plat->board_data;
 400
 401         if (is_host_enabled(musb))
 402                 del_timer_sync(&otg_workaround);
 403
 404         /* Shutdown the on-chip PHY and its PLL. */
 405         if (data->set_phy_power)
 406                 data->set_phy_power(0);
 407
 408         otg_put_transceiver(musb->xceiv);
 409         usb_nop_xceiv_unregister();
 410
 411         return 0;
 412 }
 413
 414 /* AM35x supports only 32bit read operation */
 415 void musb_read_fifo(struct musb_hw_ep *hw_ep, u16 len, u8 *dst)
 416 {
 417         void __iomem *fifo = hw_ep->fifo;
 418         u32             val;
 419         int             i;
 420
 421         /* Read for 32bit-aligned destination address */
 422         if (likely((0x03 & (unsigned long) dst) == 0) && len >= 4) {
 423                 readsl(fifo, dst, len >> 2);
 424                 dst += len & ~0x03;
 425                 len &= 0x03;
 426         }
 427         /*
 428          * Now read the remaining 1 to 3 byte or complete length if
 429          * unaligned address.
 430          */
 431         if (len > 4) {
 432                 for (i = 0; i < (len >> 2); i++) {
 433                         *(u32 *) dst = musb_readl(fifo, 0);
 434                         dst += 4;
 435                 }
 436                 len &= 0x03;
 437         }
 438         if (len > 0) {
 439                 val = musb_readl(fifo, 0);
 440                 memcpy(dst, &val, len);
 441         }
 442 }
 443
 444 static const struct musb_platform_ops am35x_ops = {
 445         .init           = am35x_musb_init,
 446         .exit           = am35x_musb_exit,
 447
 448         .enable         = am35x_musb_enable,
 449         .disable        = am35x_musb_disable,
 450
 451         .set_mode       = am35x_musb_set_mode,
 452         .try_idle       = am35x_musb_try_idle,
 453
 454         .set_vbus       = am35x_musb_set_vbus,
 455 };
 456
 457 static u64 am35x_dmamask = DMA_BIT_MASK(32);
 458
 459 static int __init am35x_probe(struct platform_device *pdev)
 460 {
 461         struct musb_hdrc_platform_data  *pdata = pdev->dev.platform_data;
 462         struct platform_device          *musb;
 463         struct am35x_glue               *glue;
 464
 465         struct clk                      *phy_clk;
 466         struct clk                      *clk;
 467
 468         int                             ret = -ENOMEM;
 469
 470         glue = kzalloc(sizeof(*glue), GFP_KERNEL);
 471         if (!glue) {
 472                 dev_err(&pdev->dev, "failed to allocate glue context\n");
 473                 goto err0;
 474         }
 475
 476         musb = platform_device_alloc("musb-hdrc", -1);
 477         if (!musb) {
 478                 dev_err(&pdev->dev, "failed to allocate musb device\n");
 479                 goto err1;
 480         }
 481
 482         phy_clk = clk_get(&pdev->dev, "fck");
 483         if (IS_ERR(phy_clk)) {
 484                 dev_err(&pdev->dev, "failed to get PHY clock\n");
 485                 ret = PTR_ERR(phy_clk);
 486                 goto err2;
 487         }
 488
 489         clk = clk_get(&pdev->dev, "ick");
 490         if (IS_ERR(clk)) {
 491                 dev_err(&pdev->dev, "failed to get clock\n");
 492                 ret = PTR_ERR(clk);
 493                 goto err3;
 494         }
 495
 496         ret = clk_enable(phy_clk);
 497         if (ret) {
 498                 dev_err(&pdev->dev, "failed to enable PHY clock\n");
 499                 goto err4;
 500         }
 501
 502         ret = clk_enable(clk);
 503         if (ret) {
 504                 dev_err(&pdev->dev, "failed to enable clock\n");
 505                 goto err5;
 506         }
 507
 508         musb->dev.parent                = &pdev->dev;
 509         musb->dev.dma_mask              = &am35x_dmamask;
 510         musb->dev.coherent_dma_mask     = am35x_dmamask;
 511
 512         glue->dev                       = &pdev->dev;
 513         glue->musb                      = musb;
 514         glue->phy_clk                   = phy_clk;
 515         glue->clk                       = clk;
 516
 517         pdata->platform_ops             = &am35x_ops;
 518
 519         platform_set_drvdata(pdev, glue);
 520
 521         ret = platform_device_add_resources(musb, pdev->resource,
 522                         pdev->num_resources);
 523         if (ret) {
 524                 dev_err(&pdev->dev, "failed to add resources\n");
 525                 goto err6;
 526         }
 527
 528         ret = platform_device_add_data(musb, pdata, sizeof(*pdata));
 529         if (ret) {
 530                 dev_err(&pdev->dev, "failed to add platform_data\n");
 531                 goto err6;
 532         }
 533
 534         ret = platform_device_add(musb);
 535         if (ret) {
 536                 dev_err(&pdev->dev, "failed to register musb device\n");
 537                 goto err6;
 538         }
 539
 540         return 0;
 541
 542 err6:
 543         clk_disable(clk);
 544
 545 err5:
 546         clk_disable(phy_clk);
 547
 548 err4:
 549         clk_put(clk);
 550
 551 err3:
 552         clk_put(phy_clk);
 553
 554 err2:
 555         platform_device_put(musb);
 556
 557 err1:
 558         kfree(glue);
 559
 560 err0:
 561         return ret;
 562 }
 563
 564 static int __exit am35x_remove(struct platform_device *pdev)
 565 {
 566         struct am35x_glue       *glue = platform_get_drvdata(pdev);
 567
 568         platform_device_del(glue->musb);
 569         platform_device_put(glue->musb);
 570         clk_disable(glue->clk);
 571         clk_disable(glue->phy_clk);
 572         clk_put(glue->clk);
 573         clk_put(glue->phy_clk);
 574         kfree(glue);
 575
 576         return 0;
 577 }
 578
 579 #ifdef CONFIG_PM
 580 static int am35x_suspend(struct device *dev)
 581 {
 582         struct am35x_glue       *glue = dev_get_drvdata(dev);
 583         struct musb_hdrc_platform_data *plat = dev->platform_data;
 584         struct omap_musb_board_data *data = plat->board_data;
 585
 586         /* Shutdown the on-chip PHY and its PLL. */
 587         if (data->set_phy_power)
 588                 data->set_phy_power(0);
 589
 590         clk_disable(glue->phy_clk);
 591         clk_disable(glue->clk);
 592
 593         return 0;
 594 }
 595
 596 static int am35x_resume(struct device *dev)
 597 {
 598         struct am35x_glue       *glue = dev_get_drvdata(dev);
 599         struct musb_hdrc_platform_data *plat = dev->platform_data;
 600         struct omap_musb_board_data *data = plat->board_data;
 601         int                     ret;
 602
 603         /* Start the on-chip PHY and its PLL. */
 604         if (data->set_phy_power)
 605                 data->set_phy_power(1);
 606
 607         ret = clk_enable(glue->phy_clk);
 608         if (ret) {
 609                 dev_err(dev, "failed to enable PHY clock\n");
 610                 return ret;
 611         }
 612
 613         ret = clk_enable(glue->clk);
 614         if (ret) {
 615                 dev_err(dev, "failed to enable clock\n");
 616                 return ret;
 617         }
 618
 619         return 0;
 620 }
 621
 622 static struct dev_pm_ops am35x_pm_ops = {
 623         .suspend        = am35x_suspend,
 624         .resume         = am35x_resume,
 625 };
 626
 627 #define DEV_PM_OPS      &am35x_pm_ops
 628 #else
 629 #define DEV_PM_OPS      NULL
 630 #endif
 631
 632 static struct platform_driver am35x_driver = {
 633         .remove         = __exit_p(am35x_remove),
 634         .driver         = {
 635                 .name   = "musb-am35x",
 636                 .pm     = DEV_PM_OPS,
 637         },
 638 };
 639
 640 MODULE_DESCRIPTION("AM35x MUSB Glue Layer");
 641 MODULE_AUTHOR("Ajay Kumar Gupta <ajay.gupta@ti.com>");
 642 MODULE_LICENSE("GPL v2");
 643
 644 static int __init am35x_init(void)
 645 {
 646         return platform_driver_probe(&am35x_driver, am35x_probe);
 647 }
 648 subsys_initcall(am35x_init);
 649
 650 static void __exit am35x_exit(void)
 651 {
 652         platform_driver_unregister(&am35x_driver);
 653 }
 654 module_exit(am35x_exit);